The morphology of nanostructures is a vital parameter to consider in components comprised of materials exhibiting specific functionalities. The number of process steps and the need for high temperatures can often be a limiting factor when targeting a specific morphology. Here, we demonstrate a repeatable synthesis of different morphologies of a highly crystalline monoclinic phase of vanadium dioxide (VO2(M)) using a one-step hydrothermal method. By adjusting the synthesis parameters, such as pH, temperature, and reducing agent concentration in the precursor, VO2 nanostructures with high uniformity and crystallinity are achieved. Some of these morphologies were obtained via the choice of the reducing agent that allowed us to skip the annealing step. Our results indicate that the morphologies of the nanostructures are very sensitive to the hydrazine hydrate (N2H4.H2O) concentration. Another reducing agent, dodecylamine, was used to achieve well-organized and high-quality VO2(M) nanotubes. Differential scanning calorimetry (DSC) experiments revealed that all samples display the monoclinic-to-tetragonal structural transition (MTST) regardless of the morphology, albeit at different temperatures that can be interpreted as the variations in overheating and undercooling limits. VO2(M) structures with a higher surface to volume ratio exhibit a higher overheating limit than those with low ratios.
A structural health monitoring (SHM) study of biaxial glass fibre-reinforced epoxy matrix composites under a constant, high strain uniaxial fatigue loading is performed using fibre Bragg grating (FBG) optical sensors embedded in composites at various locations to monitor the evolution of local strains, thereby understanding the damage mechanisms. Concurrently, the temperature changes of the samples during the fatigue test have also been monitored at the same locations. Close to fracture, significant variations in local temperatures and strains are observed, and it is shown that the variations in temperature and strain can be used to predict imminent fracture. It is noted that the latter information cannot be obtained using external strain gages, which underlines the importance of the tracking of local strains internally.
Spatial charge distribution for biased semiconductors fundamentally differs from metals since they can allow inhomogeneous charge distributions due to penetration of the electric field, as observed in the classical Schottky junctions. Similarly, the electrostatics of the dielectric/semiconductor interface can lead to a carrier depletion or accumulation in the semiconductor side when under applied bias. In this study, we demonstrate that the inhomogeneous carrier accumulation in a moderately p-doped GaAs–dielectric interface can be tailored for tunable plasmonics by an external voltage. Solving Maxwell’s equations in the doped GaAs-dielectric stack, we investigate the tunability of the surface plasmon and phonon polaritons’ interaction via an external bias. The plasmonic mode analysis of such an interface reveals interesting dispersion curves for surface plasmon and phonon polariton interactions that are not possible in metals. We show that the plasmon dispersion curve can be engineered through an external bias using the inherent properties of the p-doped GaAs– dielectric interface.
17 November 2023 in ACS Applied Electronic Materials
Ionized impurities have nearly always been neglected in discussing the limit of functionality of ferroelectric thin films. One would certainly expect that the thickness limit for functionality would be altered in the presence of ionized impurities, but how this would occur remains unclear. In this article, we analyze the domain structures as well as the phase transition temperatures in films with depletion charges for various film thicknesses. Depletion charges induce a position-dependent built-in field that leads to an inhomogeneous distribution of ferroelectric polarization. Such an inhomogeneity in the polarization results in strong depolarizing fields in films. We show that formation of saw-tooth–type domains is a way to circumvent the depolarizing fields, even in films with ideal electrodes. There is a critical film thickness above which the saw-tooth domains develop. On the other hand, the phase transition of the ultrathin structures with electrodes having a finite screening length, namely real electrodes, is always into the multidomain state during cooling from the paraelectric state, regardless of the presence of depletion charges. An important finding we have is that the transition temperature in films with real electrodes does not depend nearly at all on the depletion charge density unless it is very high (>1026 ionized impurities/m3). Relatively thick films (>8 nm in this work) with real electrodes that have very high depletion charge densities have transition temperatures very similar to those with the same charge density, but with ideal electrodes, making us conclude that thick films with high depletion charge densities will hardly feel the finite screening effects. The results are provided for (001) BaTiO3 films grown on (001) SrTiO3 substrates with pseudomorphic top and bottom metallic electrodes.