Three-dimensional (3D) printing technologies are based on successive material printing layer-by-layer and are considered suitable for the production of dosage forms customized for a patient’s needs. In this study, tablets of atomoxetine hydrochloride (ATH) have been successfully fabricated by a digital light processing (DLP) 3D printing technology. Initial materials were photoreactive suspensions, composed of poly(ethylene glycol) diacrylate 700 (PEGDA 700), poly(ethylene glycol) 400 (PEG 400), photoinitiator and suspended ATH. The amount of ATH was varied from 10.00 to 25.00% (w/w), and a range of doses from 12.21 to 40.07 mg has been achieved, indicating the possibility of personalized therapy. The rheological characteristics of all photoreactive suspensions were appropriate for the printing process, while the amount of the suspended particles in the photoreactive suspensions had an impact on the 3D printing process, as well as on mechanical and biopharmaceutical characteristics of tablets. Only the formulation with the highest content of ATH had significantly different tensile strength compared to other formulations. All tablets showed sustained drug release during at least the 8h. ATH crystals were observed with polarized light microscopy of photoreactive suspensions and the cross-sections of the tablets, while no interactions between ATH and polymers were detected by FT-IR spectroscopy.

Selective laser sintering (SLS) is a rapid prototyping technique for the production of three-dimensional objects through selectively sintering powder-based layer materials. The aim of the study was to investigate the effect of energy density (ED) and formulation factors on the printability and characteristics of SLS irbesartan tablets. The correlation between formulation factors, ED, and printability was obtained using a decision tree model with an accuracy of 80%. FT-IR results revealed that there was no interaction between irbesartan and the applied excipients. DSC results indicated that irbesartan was present in an amorphous form in printed tablets. ED had a significant influence on tablets’ physical, mechanical, and morphological characteristics. Adding lactose monohydrate enabled faster drug release while reducing the possibility for printing with different laser speeds. However, formulations with crospovidone were printable with a wider range of laser speeds. The adjustment of formulation and process parameters enabled the production of SLS tablets with hydroxypropyl methylcellulose with complete release in less than 30 min. The results suggest that a decision tree could be a useful tool for predicting the printability of pharmaceutical formulations. Tailoring the characteristics of SLS irbesartan tablets by ED is possible; however, it needs to be governed by the composition of the whole formulation.

Background: Since the beginning of the HIV/AIDS epidemic, 75 million people have been infected with the HIV and about 32 million people have died of AIDS. Investigation of the molecular mechanisms critical to the HIV replication cycle led to the identification of potential drug targets for AIDS therapy. One of the most important discoveries is HIV-1 protease, an enzyme that plays an essential role in the replication cycle of HIV.Objective: The aim of the present study is to synthesize and investigate anti-HIV-1 protease activity of some chalcone derivatives with the hope of discovering new lead structure devoid drug resistance.Methods: 20 structurally similar chalcone derivatives were synthesized and their physico-chemical characterization was performed. Binding of chalcones to HIV-1 protease was investigated by fluorimetric assay. Molecular docking studies were conducted to understand the interactions.Results: The obtained results revealed that all compounds showed anti-HIV-1 protease activity. Compound C1 showed the highest inhibitory activity with an IC50 value of 0.001 μM, which is comparable with commercial product Darunavir.Conclusion: It is difficult to provide general principles of inhibitor design. Structural properties of the compounds are not the only consideration; ease of chemical synthesis, low molecular weight, bioavailability, and stability are also of crucial importance. Compared to commercial products the main advantage of compound C1 is the ease of chemical synthesis and low molecular weight. Furthermore, compound C1 has a structure that is different to peptidomimetics, which could contribute to its stability and bioavailability.

Background/Objectives: Selective laser sintering (SLS) is one of the most promising 3D printing techniques for pharmaceutical applications as it offers numerous advantages, such as suitability to work with already approved pharmaceutical excipients, the elimination of solvents, and the ability to produce fast-dissolving, porous dosage forms with high drug loading. When the powder mixture is exposed to elevated temperatures during SLS printing, the active ingredients can be converted from the crystalline to the amorphous state, which can be used as a strategy to improve the dissolution rate and bioavailability of poorly soluble drugs. This study investigates the potential application of SLS 3D printing for the fabrication of tablets containing the poorly soluble drug carvedilol with the aim of improving the dissolution rate of the drug by forming an amorphous form through the printing process. Methods: Using SLS 3D printing, eight tablet formulations were produced using two different powder mixtures and four combinations of experimental conditions, followed by physicochemical characterization and dissolution testing. Results: Physicochemical characterization revealed that at least partial amorphization of carvedilol occurred during the printing process. Although variations in process parameters were minimal, higher temperatures in combination with lower laser speeds appeared to facilitate a greater degree of amorphization. Ultimately, the partial conversion to the amorphous form significantly improved the dissolution of carvedilol compared to its pure crystalline form. Conclusions: Obtained results suggest that the SLS 3D printing technique can be effectively used to convert poorly water-soluble drugs to their amorphous state, thereby improving solubility and bioavailability.