The aim of this study was to determine the optimal conditions for dark fermentation using agro-industrial liquid wastewaters mixed with sweet sorghum stalks (i.e., 55% sorghum, 40% cheese whey, and 5% liquid cow manure). Batch experiments were performed to investigate the effect of controlled pH (5.0, 5.5, 6.0, 6.5) on the production of bio-hydrogen and volatile fatty acids. According to the obtained results, the maximum hydrogen yield of 0.52 mol H₂/mol eq. glucose was measured at pH 5.5 accompanied by the highest volatile fatty acids production, whereas similar hydrogen productivity was also observed at pH 6.0 and 6.5. The use of heat-treated anaerobic sludge as inoculum had a positive impact on bio-hydrogen production, exhibiting an increased yield of 1.09 mol H₂/mol eq. glucose. On the other hand, the pretreated (ensiled) sorghum, instead of a fresh one, led to a lower hydrogen production, while the organic load decrease did not affect the process performance. In all experiments, the main fermentation end-products were volatile fatty acids (i.e., acetic, propionic, butyric), ethanol and lactic acid.

The need for alternative energy sources is constantly growing worldwide, while the focus has shifted to the valorization of biomass. The aim of the present study was to determine the optimal pH and hydraulic retention time (HRT) values for treating a mixture of sorghum biomass solution with liquid cow manure (in a ratio 95:5 v/v) through anaerobic digestion, in a two-stage system. Batch tests were initially carried out for the investigation of the pH effect on bio-hydrogen and volatile fatty acids (VFA) production. The highest hydrogen yield of 0.92 mol H₂/mol carbohydrates_consumed was obtained at pH 5.0, whereas the maximum degradation of carbohydrates and VFA productivity was observed at pH 6.0. Further investigation of the effect of HRT on hydrogen and methane production was carried out. The maximum yield of 1.68 mol H₂/mol carbohydrates_consumed was observed at an HRT of 5 d, with H₂ productivity of 0.13 L/L_R·d. On the other hand, the highest CH₄ production rate of 0.44 L/L_R·d was achieved at an HRT of 25 d, with a methane yield of 295.3 mL/g VS_added, whereas at a reduced HRT of 20 d the process exhibited inhibition and/or overload, as indicated by an accumulation of VFAs and decline in CH₄ productivity.

The growing interest in processes that involve biomass conversion to renewable energy, such as anaerobic digestion, has stimulated research in this field in order to assess the optimum conditions for biogas production from abundant feedstocks, like agro-industrial wastes. Anaerobic digestion is an attractive process for the decomposition of organic wastes via a complex microbial consortium and subsequent conversion of metabolic intermediates to hydrogen and methane. The present study focused on the exploitation of liquid cow manure (LCM) and cheese whey (CW) as noneasily and easily biodegradable sources, respectively, using continuous stirred-tank reactors for biogas production, and a comparison was presented between single- and two-stage anaerobic digestion systems. No significant differences were found concerning LCM treatment, in a two-stage system compared to a single one, concluding that LCM can be treated by implementing a single-stage process, as a recalcitrant substrate, with the greatest methane production rate of 0.67 L CH₄/(L_R·d) at an HRT of 16 d. On the other hand, using the easily biodegradable CW as a monosubstrate, the two-stage process was considered a better treatment system compared to a single one. During the single-stage process, operational problems were observed due to the limited buffering capacity of CW. However, the two-stage anaerobic digestion of CW produced a stable methane production rate of 0.68 L CH₄/(L_R·d) or 13.7 L CH₄/L_feed, while the total COD was removed by 76%.

The effect of copper oxide and zinc oxide nanoparticles (NPs) on the mechanical and thermal properties of ground waste concrete inorganic polymers (GWC IPs) has been investigated. NPs are added to GWC IPs at loadings of 0.1, 0.5, 1, and 2% w/w. The phase composition and microstructure of NPs GWC IPs have also been examined using X-ray diffraction (XRD), Raman spectroscopy and scanning electron microscope (SEM/EDS) techniques. Results show that the mechanical properties of GWC IPs are improved (23 MPa) due to addition of NPs (1% ZnO). In particular, GWC IPs embedded with 0.5% CuO and 1% ZnO NPs exhibited relatively improved compressive strength. The addition of NPs decreases the macroporosity and increases the mesoporosity of IPs matrix and decreases relatively the ability of IPs matrix to water absorption. The antimicrobial activity of GWC IPs doped with 0.5 and 1% CuO NPs against E. coli was also determined.