YFeO3, YFe0.95Co0.05O3, Y0.95Gd0.05FeO3 and Y1−xGdxFe0.95Co0.05O3 (x = 0.0, 0.05, 0.10, 0.15 and 0.20) nanopowders were successfully fabricated via a low-temperature solid-state reaction technique. Results obtained using X-ray diffraction (XRD), scanning electron microscopy (SEM), and Raman spectra indicate that YFeO3 nanopowders with Gd3+ and Co3+ ions co-doping at Y and Fe-sites were fabricated at 800 °C in sizes below 50 nm, and a distorted structure was obtained. Magnetic hysteresis loop analyses illustrate that ferromagnetic behavior of YFeO3 nanopowders can be enhanced with the addition of Gd and Co. Whereas the maximum and remnant magnetization of the powders were found to be about 5.24 and 2.6 emu/g, respectively, the optical band gap was around 2.4 eV, proving that co-doped YFeO3 nanopowders have a strong capability to absorb visible light. Because both magnetic and optical properties of these materials are greatly improved with the addition of Gd and Co, one can expect the scope of their potential application in the magnetic and optical fields to increase.
Based on precursor powders with a size of 200–300 nm prepared by the low-temperature solid reaction method, phase-pure YFeO3 ceramics are fabricated using spark plasma sintering (SPS) at different temperatures. X-ray diffraction (XRD) and scanning electron microscopy (SEM) reveal that the high-purity YFeO3 ceramics can be prepared using SPS, while the results from X-ray photoelectron spectroscopy (XPS) show that the concentration of oxygen vacancies resulting from transformation from Fe3+ to Fe2+ is low. The relative density of the 1000 °C-sintered sample is as high as 97.7%, which is much higher than those of the samples sintered at other temperatures. The present dielectric and magnetic properties are much better than those of the samples fabricated by conventional methods. These findings indicate that the YFeO3 ceramics prepared by the low temperature solid reaction and SPS methods possess excellent dielectric and magnetic properties, making them suitable for potential applications involving magnetic storage.
Phase-pure hexagonal and orthorhombic YFeO3 nanopowders are synthesized by low-temperature solid-state reaction along with Zr doping. The obtained powders are characterized by X-ray diffraction, field emission scanning electron microscopy, and physical property measurements. The hexagonal YFeO3 exhibits a narrower optical band gap in comparison to the orthorhombic one, while the orthorhombic YFeO3 presents better magnetic properties. The formation of hexagonal or orthorhombic phase can be effectively controlled by Zr doping. The temperature range of synthesizing the hexagonal YFeO3 nanopowders is increased by ~200 °C due to Zr doping so that they can be easily synthesized, which possesses a finer particle size and a smaller optical band gap, making it favorable for optical applications.
28 May 2010 in Journal of Materials Science: Materials in Electronics
Based on precursor powders with a size of 200–300 nm prepared by the low-temperature solid-state reaction method, phase-pure YMnO3 ceramics are fabricated using spark plasma sintering (SPS). X-ray diffraction (XRD) and scanning electron microscopy (SEM) reveal that the high-purity YMnO3 ceramics can be prepared by SPS at 1000 °C for 5 minutes with annealing at 800 °C for 2 h. The relative density of the sample is as high as 97%, which is much higher than those of the samples sintered by other methods. The present dielectric and magnetic properties are much better than those of the samples fabricated by conventional methods and SPS with ball-milling precursors, and the ferroelectric loops at room temperature can be detected. These findings indicate that the YMnO3 ceramics prepared by the low temperature solid reaction method and SPS possess excellent dielectric lossy ferroelectric properties at room temperature, and magnetic properties at low temperature (10 K), making them suitable for potential multiferroic applications.
Aluminum–silicon (Al–Si) alloys are the most commonly cast aluminum alloys. Fe is the most deleterious element for Al–Si die casting alloys, as its existence causes the precipitation of substantial intermetallics that result in the unsatisfactory mechanical performance of the alloy, such as its ductility. Hence, controlling the morphology and formation of the AlFeSi phase, particularly the β-AlFeSi phase, is vital for improving the ductility of Al–Si die casting alloys. Herein, Ca was added to the A380 alloy, and the morphological changes resulting from the influence of Ca on the AlFeSi phase were characterized. The outcomes revealed that according to different cooling rates, specific amounts of Ca addition (0.01–0.1 wt.%) were capable of refining α-AlFeSi and β-AlFeSi morphology and transforming the β-AlFeSi phase into α-AlFeSi. Moreover, Ca addition could also modify eutectic silicon. The transformation mechanism and refining role of Ca in AlFeSi and the different morphologies of Al2CaSi2 were analyzed.