Coconut fiber is a natural fiber extracted from coconut coir, a by-product of coconut based product. It is a potential material for fiberboard because it contains high cellulose and lignin which is similar to wood. Binderless medium density fiberboard (MDF) from coconut fiber was produced to reduce the consumption of wood and the emmission of synthetic adhesives such as urea formaldehyde using lignin as natural binder. The purpose of this research were to determine the physical and mechanical properties of MDF from coconut fiber based on SNI 01-4449-2006 and JIS A 5905:2003 and to investigate the effect of oxidation treatment, additional paraffin, and pressing time to the physical and mechanical properties of the fiberboard. The results showed that the fiberboards produced on this research had medium density of 0.44-0.56 g/cm3 which met the standard for MDF. Most of fiberboards from coconut fiber obtained in this study met the standard for physical properties such as density, moisture content, thickness swelling, and screw holding power. However, the mechanical properties such as modulus of elasticity, modulus of rupture, and internal bond of the fiberboards had not met the SNI 01-4449-2006 and JIS A 5905:2003 because of the lack of materials strength.
14 April 2020 in International Journal of Technology
Boiler ash is a second layer by-product of the combustion of fuel, usually an agro-waste, in any industry. In the sugarcane industry, boiler ash is obtained from the combustion of bagasse. The boiler ash of the sugarcane industry contains 49.69% silica, which can be transformed into nano-silica using the precipitation method, which is easier and cheaper than other methods. Precipitation pH and aging time are the main factors that influence nano-silica’s characteristics. The objectives of this research were to determine the effect of various precipitation pH levels and aging times on the characteristics of nano-silica and to identify the potential applications of nano-silica based on these characteristics. An increase in precipitation pH affected the number of the crystal phase and the intensity of the diffraction peaks. An increase in aging time also affected the intensity of the diffraction peaks and the number of crystal phases. The degree of crystallinity varied from 66.40% to 93.53%, the crystal size ranged from 37.77 nm to 56.87 nm, the particle size ranged from 214.04 nm to 698.24 nm, and the polydispersity index (PDI) ranged from 0.21 to 0.83. The nano-silica in this research had polygonal morphology. Increases in precipitation pH and aging time increased the number of siloxane groups, creating nano-silica dominated by a crystalline form with three crystal phases: tridymite, quartz, and cristobalite. Nano-silica have various potential applications based on their characteristics, including as filler for membranes, composite resin, rubber airbags, and supplementary cementitious material.
10 July 2017 in International Journal of Productivity and Performance Management
Purpose: The purpose of this paper is to develop a spatial intelligent decision support system (SIDSS) for increasing productivity in the rubber agroindustry by green productivity (GP) approach. The SIDSS was used to measure the productivity of rubber plantation and rubber agroindustry by GP approach, and select the best strategies for increasing the productivity of rubber agroindustry. Design/methodology/approach: This system was developed by combining spatial analysis, GP, and fuzzy analytic network process (ANP) with the model-based management system, which is able to provide comprehensive and meaningful decision alternatives for the development of natural rubber agroindustry. Rubber plantation productivity measurement model was used to find the productivity level of rubber plantation with fuzzy logic, and also to provide information and decision alternatives to all stakeholders regarding spatial condition of rubber agroindustry, production process flow, and analysis of the seven green wastes at each production process flow using the geographic information system. GP measurement model was used to determine the productivity performance of the rubber agroindustry with the green productivity index (GPI). The best strategy for increasing the productivity was determined with fuzzy ANP. Findings: Rubber plantation measurement model showed that the average of plantation productivity was 6.25 kg/ha/day. GP measurement model showed that the GPI value of ribbed smoked sheet (RSS) was 0.730, whereas of crumb rubber (CR) was 0.126. The best strategy for increasing the productivity of rubber agroindustry was raw material characteristics control. Based on the best strategy, the GPI value of RSS was 1.340, whereas of CR was 0.228. Research limitations/implications: This decision support system is still limited as it is based on static data; it needs further development so that it can be more dynamically based on developments in the rubber agroindustry related levels of productivity and environmental impact. In addition, details regarding the decision to increase the productivity of the rubber section by benchmarking efforts should be studied further, both among plantation as well as among countries such as Thailand so that the productivity of rubber plantation and agroindustry can be integrated. Practical implications: This research can help the planters to select superior clones for rubber trees, to improve the technique of tapping latex, and to use a better coagulant. The good quality and quantity of raw material is a key factor in increasing the productivity of rubber agroindustry; if the quality of latex is good then the resulting product will also have a good quality and production cost can be reduced. In addition, the application of GP through the calculation of GPI value using improvement scenarios can be used as a reference and comparison for evaluating the performance of rubber agroindustry to reduce the waste generated by the activities of rubber processing plant. Social implications: Reduction of waste generated by production activities can improve the quality of life of the workforce and the environment. The calculation of GPI value can also be used as a basis to use raw materials, water, and electricity more efficiently. Originality/value: This system was developed by combining spatial analysis, GP, and fuzzy ANP with the model-based management system, which is able to provide comprehensive and meaningful decision alternatives for the development of natural rubber agroindustry.
1 October 2023 in Journal of Ecological Engineering
Empty oil palm bunches (EFB) can be converted by hydrothermal carbonation process into biochar that can be used as low-cost adsorbent. This study aims to identify the effects of pretreatment and post-treatment using alkaline activators on the biochar characteristics produced from EFB. The...
1 November 2017 in Jurnal Teknologi Industri Pertanian
Bagasse ashes have high silica content thus it can be used in nanosilicaproduction to increase its benefit value. This study aimed to get the best time for synthesis and to determine the optimum synthesis time and temperature. This study used the hydrothermal method, a simple method with relatively low reaction temperature and provide a good chemical homogeneity. Time varieties in synthesizing silica were 8,10 and 12 hours, at the temperature of 150 ᴼC. But the results were not as expected. Moreover, optimization of synthesis temperature and time used 4 hours at the temperature of 150 ᴼC based on previous studies. Optimization was conducted using the Response Surface Methodology (RSM). Later, a testusing PSA (Particle Size Analyzer) was performed to obtain particle sizes and PDI values (Polydispersity Index). The results showed that the prediction model of temperature synthesis was 152.67 ᴼC, synthesis time of 6 hours, particle size of 276.288 nm and PDI value of 0.189642. The tests showed that the size of particle obtained was 330.39 nm and PDI value at 0.3580. Actual results and predicted results were not significant different.