Mohsen Ayoobi

Prof. Dr. Mohsen Ayoobi

Division of Engineering Technology, Wayne State University, Detroit, MI 48201 USA
orcid

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
5 June 2017 in International Journal of Spray and Combustion Dynamics
Verified
Journal Article
Open access
MAMohsen Ayoobi
Mohsen Ayoobi
ISIngmar Schoegl
Ingmar Schoegl
Premixed flames propagating within small channels show complex combustion phenomena that differ from flame propagation at conventional scales. Available experimental and numerical studies have documented stationary, non-stationary, or asymmetric modes that depend on properties of the incoming reactant flow as well as channel geometry and wall temperatures. This work seeks to illuminate mechanisms leading to symmetry breaking and limit cycle behavior that are fundamental to these combustion modes. Specifically, four cases of lean premixed methane/air combustion—two equivalence ratios (0.53 and 0.7) and two channel widths (2 mm and 5 mm)—are investigated in a 2D configuration with constant channel length and bulk inlet velocity, where numerical simulations are performed using detailed chemistry. External wall heating is simulated by imposing a linear temperature gradient as a boundary condition on both walls. In the 2 mm channel, both equivalence ratios produce flames that stabilize with symmetric flame fronts after propagating upstream. In the 5 mm channel, flame fronts start symmetrically, although symmetry is broken almost immediately after ignition. Further, 5 mm channels produce non-stationary combustion modes with dramatically different limit cycles: in the leaner case (φ = 0.53), the asymmetric flame front flops periodically, whereas in the richer case (φ = 0.7), flames with repetitive extinctions and ignitions (FREI) are observed. To further understand the flame dynamics, reaction fronts and flame fronts are captured and differentiated. Results show that the loss of flame front symmetry originates in a region close to the flame cusp, where flow and chemical characteristics exhibit large gradients and curvatures. Limit cycle behavior is illuminated by investigating flame edges that are formed along the wall, and accompany local or global ignition and extinction processes. In the flopping mode (φ = 0.53), local ignition and extinction in regions adjacent to the wall result in oblique fronts that advance and recede along the wall and redirect the flow ahead of the flame. In the FREI mode, asymmetric flames propagate much farther upstream, where they experience global extinction due to heat losses, and re-ignite far downstream with opposite flame front orientation. In both cases, an interaction of flow and chemical effects drives the asymmetric limit cycles. The lack of instabilities and asymmetries for the 2mm cases is attributed to insufficient wall separation, which is of the same order of magnitude as the flame thickness.

15 August 2019 in Applied Sciences
Verified
Journal Article
Open access
PDF file
PRPedro Resende
Pedro Resende
MAMohsen Ayoobi
Mohsen Ayoobi
Alexandre AfonsoAlexandre Afonso
Alexandre Afonso
With the increasing global concerns about the impacts of byproducts from the combustion of fossil fuels, researchers have made significant progress in seeking alternative fuels that have cleaner combustion characteristics. Such fuels are most suitable for addressing the increasing demands on combustion-based micro power generation systems due to their prominently higher energy density as compared to other energy resources such as batteries. This cultivates a great opportunity to develop portable power devices, which can be utilized in unmanned aerial vehicles (UAVs), micro satellite thrusters or micro chemical reactors and sensors. However, combustion at small scales—whether premixed or non-premixed (diffusion)—has its own challenges as the interplay of various physical phenomena needs to be understood comprehensively. This paper reviews the scientific progress that researchers have made over the past couple of decades for the numerical investigations of diffusion flames at micro scales. Specifically, the objective of this review is to provide insights on different numerical approaches in analyzing diffusion combustion at micro scales, where the importance of operating conditions, critical parameters and the conjugate heat transfer/heat re-circulation have been extensively analyzed. Comparing simulation results with experimental data, numerical approaches have been shown to perform differently in different conditions and careful consideration should be given to the selection of the numerical models depending on the specifics of the cases that are being modeled. Varying different parameters such as fuel type and mixture, inlet velocity, wall conductivity, and so forth, researchers have shown that at micro scales, diffusion combustion characteristics and flame dynamics are critically sensitive to the operating conditions, that is, it is possible to alter the flammability limits, control the flame stability/instability or change other flame characteristics such as flame shape and height, flame temperature, and so forth.

16 November 2018 in Journal of Heat Transfer
Verified
Journal Article
Closed access
PDF file
PRPedro Resende
Pedro Resende
Alexandre AfonsoAlexandre Afonso
Alexandre Afonso
CPCarlos Pinho
Carlos Pinho
MAMohsen Ayoobi
Mohsen Ayoobi


11 July 2021 in Energies
Verified
Journal Article
Open access
PDF file
SPSunita Pokharel
Sunita Pokharel
MAMohsen Ayoobi
Mohsen Ayoobi
V'yacheslav AkkermanV'yacheslav Akkerman
V'yacheslav Akkerman
Due to increasing demand for clean and green energy, a need exists for fuels with low emissions, such as synthetic gas (syngas), which exhibits excellent combustion properties and has demonstrated promise in low-emission energy production, especially at microscales. However, due to complicated flame properties in microscale systems, it is of utmost importance to describe syngas combustion and comprehend its properties with respect to its boundary and inlet conditions, and its geometric characteristics. The present work studied premixed syngas combustion in a two-dimensional channel, with a length of 20 mm and a half-width of 1 mm, using computational approaches. Specifically, a fixed temperature gradient was imposed at the upper wall, from 300 K at the inlet to 1500 K at the outlet, to preheat the mixture, accounting for the conjugate heat transfer through the walls. The detailed chemistry of the ignition process was imitated using the San Diego mechanism involving 46 species and 235 reactions. For the given boundary conditions, stoichiometric premixed syngas containing various compositions of carbon monoxide, methane, and hydrogen, over a range of inlet velocities, was simulated, and various combustion phenomena, such as ignition, flame stabilization, and flames with repeated extinction and ignition (FREI), were analyzed using different metrics. The flame stability and the ignition time were found to correlate with the inlet velocity for a given syngas mixture composition. Similarly, for a given inlet velocity, the correlation of the flame properties with respect to the syngas composition was further scrutinized.

21 September 2023 in Energies
Verified
Journal Article
Open access
PDF file
AKAlmoutazbellah Adnan Kutkut
Almoutazbellah Adnan Kutkut
MAMohsen Ayoobi
Mohsen Ayoobi
MBMarc E. Baumgardner
Marc E. Baumgardner
V'yacheslav AkkermanV'yacheslav Akkerman
V'yacheslav Akkerman
Understanding and improving the performance of miniature devices powered by micro-combustion have been the focus of continued attention of researchers recently. The goal of the present work is to investigate the behavior of premixed methane–air combustion in a quartz microreactor with an externally controlled wall temperature. Specifically, the impacts of the flow inlet velocity, the equivalence ratio, and the microreactor channel size are examined. This study is conducted by means of computational simulations, and the results are validated against prior experimental data, as well as by other similar studies in the literature. Utilizing simulation results with detailed chemistry, the present work provides more in-depth insight into a variety of phenomena, such as ignition, flame propagation, flames with repetitive extinctions and ignitions (FREI), and flame stabilization. In particular, the ignition, the flame span, and the FREI-related characteristics are scrutinized to understand the underlying physics of the flame stability/instability modes. It is shown that the flames appear stable at higher inlet velocities, while the FREI mode is detected at a lower inlet velocity, depending on the equivalence ratio and the channel size. The findings also explain how different operating conditions impact the flame characteristics in both stability modes.