Ruimin Shi

Dr. Ruimin Shi

orcid

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
28 August 2019 in Materials
Verified
Journal Article
Open access
PDF file
RSRuimin Shi
Ruimin Shi
BWBukang Wang
Bukang Wang
ZYZhiwei Yan
Zhiwei Yan
ZWZongyan Wang
Zongyan Wang
LDLei Dong
Lei Dong
In order to explore the relationship between the surface topography parameters and friction properties of a rough contact interface under fluid dynamic pressure lubrication conditions, friction experiments were carried out. The three-dimensional surface topography of specimens was measured and characterized with a profile microscopy measuring system and scanning electron microscope. The friction coefficient showed a trend of decreasing first and then increasing with the increase in some surface topography parameters at lower pressure, such as the surface height arithmetic mean Sa, surface height distribution kurtosis Sku, surface volume average volume Vvv, and surface center area average void volume Vvc, which are the ISO 25178 international standard parameters. The effects of surface topographic parameters on friction were analyzed and the wear mechanism of the worn surface was presented. The wear characteristics of the samples were mainly characterized as strain fatigue, grinding, and scraping. The results provide a theoretical basis for the functional characterization of surface topography.

14 June 2022 in Entropy
Verified
Journal Article
Open access
PDF file
RSRuimin Shi
Ruimin Shi
BWBukang Wang
Bukang Wang
ZWZongyan Wang
Zongyan Wang
JLJiquan Liu
Jiquan Liu
XFXinyu Feng
Xinyu Feng
LDLei Dong
Lei Dong
Due to the influence of signal-to-noise ratio in the early failure stage of rolling bearings in rotating machinery, it is difficult to effectively extract feature information. Variational Mode Decomposition (VMD) has been widely used to decompose vibration signals which can reflect more fault omens. In order to improve the efficiency and accuracy, a method to optimize VMD by using the Niche Genetic Algorithm (NGA) is proposed in this paper. In this method, the optimal Shannon entropy of modal components in a VMD algorithm is taken as the optimization objective, by using the NGA to constantly update and optimize the combination of influencing parameters composed of α and K so as to minimize the local minimum entropy. According to the obtained optimization results, the optimal input parameters of the VMD algorithm were set. The method mentioned is applied to the fault extraction of a simulated signal and a measured signal of a rolling bearing. The decomposition process of the rolling-bearing fault signal was transferred to the variational frame by the NGA-VMD algorithm, and several eigenmode function components were obtained. The energy feature extracted from the modal component containing the main fault information was used as the input vector of a particle swarm optimized support vector machine (PSO-SVM) and used to identify the fault type of the rolling bearing. The analysis results of the simulation signal and measured signal show that: the NGA-VMD algorithm can decompose the vibration signal of a rolling bearing accurately and has a better robust performance and correct recognition rate than the VMD algorithm. It can highlight the local characteristics of the original sample data and reduce the interference of the parameters selected artificially in the VMD algorithm on the processing results, improving the fault-diagnosis efficiency of rolling bearings.

30 April 2022 in Lubricants
Verified
Journal Article
Open access
PDF file
RSRuimin Shi
Ruimin Shi
BWBukang Wang
Bukang Wang
JLJiquan Liu
Jiquan Liu
ZYZhiwei Yan
Zhiwei Yan
LDLei Dong
Lei Dong
With the increasing market demand for artificial hip joints, total hip joint replacement has gradually become an effective means of treating a series of hip joint diseases. In order to improve the service life of artificial hip joints, some new artificial hip joint materials, including polyetheretherketone (PEEK) and carbon fiber reinforced polyetheretherketone (CFR-PEEK), have been developed. In this paper, pin-on-plate wear tests under different cross-shear ratios and contact pressures were carried out to study the wear mechanism and worn surface topography of PEEK and CFR-PEEK. The experimental results showed that the wear of PEEK was associated with cross-shear, while CFR-PEEK was not. When the cross-shear ratio was 0.039 and contact pressure was 3.18 MPa, PEEK had poor wear resistance and its wear factor was about eight times that of ultra-high molecular weight polyethylene (UHMWPE). The wear resistance of CFR-PEEK had a significant advantage, since its wear factor was about 30% of that of PEEK. The wear factors of PEEK and CFR-PEEK increased as the contact pressure increased. The arithmetic average of the height amplitude of the surface, Sa, also increased gradually according to the topography of the worn surface. The wear mechanisms of PEEK and CFR-PEEK were scratching, plough cutting, and abrasion Since CFR-PEEK had good wear resistance and insensitivity to cross-shear motion, it is suitable for making artificial hip joints under low contact pressure condition.

17 August 2020 in Research Square
Verified
Preprint
Open access
PDF file
LDLei Dong
Lei Dong
SZSiyu Zhai
Siyu Zhai
BWBukang Wang
Bukang Wang
LDLiang Dong
Liang Dong
JWJunyuan Wang
Junyuan Wang
RSRuimin Shi
Ruimin Shi
To explore the relationship between the cutting vibration and the cutting load of a single pick, this paper studied a new method for a single pick cutting rock load identification. This paper improved the low accuracy problem of the regularization method in the inverse process of frequency response function in the traditional load identification method by introducing a filter operator. By combining the inverse pseudo excitation method and the improved regularization method, the identification of the load dependent on the vibration signal was realized. A single pick cutting rock test equipment was built, which could simulate the actual working conditions of pick cutting rock in underground or tunnel. By changing cutting speed, cutting angle, cutting line spacing and cutting depth of the single pick, the change trends of real cutting load and identification load were obtained. The load identification method proposed in this paper was consistent with the change trend of the real load under the single pick cutting state. Therefore, the method had good recognition accuracy and the maximum load recognition error was 17.35%. Compared with the traditional load identification method, the identification error was reduced by a maximum of 1.98%. This method can identify the cutting load of single pick and modify the morbidity problem of frequency response function matrix. The method has a better recognition effect on the cutting load of the pick than the traditional recognition method. The research could benefit for the design of the cutting system and the arrangement of the pick on the coal mine or tunneling machinery.

30 October 2026 in Machines
Verified
Journal Article
Open access
PDF file
玉李玉虎 李
玉虎 李
PGPEI GAO
PEI GAO
RSRuimin Shi
Ruimin Shi
Joint clearance, friction, and strut flexibility interact in 6-UPS Stewart platforms, particularly during low-speed reversals, small-amplitude motions, and contact-state transitions. Treating these effects independently can omit feedback among contact geometry, normal load, friction, and strut deformation. This study develops a geometrically consistent three-dimensional closed-loop dynamic model using actual spherical-joint geometry and an equivalent representation of universal joints along their primary load-bearing directions. Normal, tangential, and axial Jacobian matrices are derived, and a nonnegative hysteretic contact model, a vector LuGre friction model under time-varying normal loads, and configuration-dependent strut flexibility are integrated. Numerical simulations were used to evaluate the proposed model through time-step convergence analysis and energy-balance assessment, as well as comparisons with models that omit some of the physical coupling effects. For the simulated intermittent-contact case, the full closed-loop model yields a root-mean-square normalized energy-balance residual of 0.0976%. Compared with the simple additive model, it predicts 326.04% greater maximum strut deformation and 32.33% greater peak normal contact force, but a 53.95% lower peak friction-force magnitude; the global position and orientation tracking errors remain comparable. The results show that comparable global tracking errors can coexist with substantial differences in local dynamic responses. This highlights the importance of closed-loop coupling in predicting local load transfer and maintaining energy-balance consistency. The proposed model provides a theoretical basis for dynamic analysis and parameter optimization of parallel mechanisms with joint clearances.