In Vietnam,Physalis angulata L.is a wild species growing throughout the country that is often used in traditional medicine. The aim of study was to quantify seven major compounds, including phenolic acids (chlorogenic acid, caffeic acid, p-coumaric acid) and flavonoids (rutin, quercitrin, quercetin, and kaempferol) in three aerial parts ofP. angulata. Chromatographic separation was carried out on a Kromasil C₁₈column (150 mm × 4.6 mm i.d., 5 µm) with a gradient elution of 0.1% formic acid in acetonitrile, 0.2% ammonium acetate/0.1% formic acid in water and methanol at a flow rate of 1.0 mL/min; detection was at 250 and 300 nm. The limits of detection and quantification were in the ranges of 0.1–0.3 and 0.3–1.0 µg/mL, respectively. The validated method was successfully applied to analyze active compounds inP. angulataand may be a useful tool for quality control of this plant.

The development of nanocomposite photocatalysts with high photocatalytic activity, cost-effectiveness, a simple preparation process, and scalability for practical applications is of great interest. In this study, nanocomposites of TiO₂ Degussa P25 nanoparticles/activated carbon (TiO₂/AC) were prepared at various mass ratios of (4:1), (3:2), (2:3), and (1:4) by a facile process involving manual mechanical pounding, ultrasonic-assisted mixing in an ethanol solution, paper filtration, and mild thermal annealing. The characterization methods included XRD, SEM-EDS, Raman, FTIR, XPS, and UV-Vis spectroscopies. The effects of TiO₂/AC mass ratios on the structural, morphological, and photocatalytic properties were systematically studied in comparison with bare TiO₂ and bare AC. TiO₂ nanoparticles exhibited dominant anatase and minor rutile phases and a crystallite size of approximately 21 nm, while AC had XRD peaks of graphite and carbon and a crystallite size of 49 nm. The composites exhibited tight decoration of TiO₂ nanoparticles on micron-/submicron AC particles, and uniform TiO₂/AC composites were obtained, as evidenced by the uniform distribution of Ti, O, and C in an EDS mapping. Moreover, Raman spectra show the typical vibration modes of anatase TiO₂ (e.g., E_1g⁽¹⁾, B_1g⁽¹⁾, E_g⁽³⁾) and carbon materials with D and G bands. The TiO₂/AC with (4:1), (3:2), and (2:3) possessed higher reaction rate constants (k) in photocatalytic degradation of methylene blue (MB) than that of either TiO₂ or AC. Among the investigated materials, TiO₂/AC = 4:1 achieved the highest photocatalytic activity with a high k of 55.2 × 10⁻³ min⁻¹ and an MB removal efficiency of 96.6% after 30 min of treatment under UV-Vis irradiation (120 mW/cm²). The enhanced photocatalytic activity for TiO₂/AC is due to the synergistic effect of the high adsorption capability of AC and the high photocatalytic activity of TiO₂. Furthermore, TiO₂/AC promotes the separation of photoexcited electron/hole (e⁻/h⁺) pairs to reduce their recombination rate and thus enhance photocatalytic activity. The optimal TiO₂/AC composite with a mass ratio of 4/1 is suggested for treating industrial or household wastewater with organic pollutants.

Lotus and Green Tea leaves are two frequently used medicinal plants in Vietnam, utilized as food, drink, or in traditional treatments to help with weight loss and cholesterol reduction. The study’s major goal is to determine the parameters of the process preparation in order to generate instant tea powder that satisfies quality criteria for customer demand. Twenty experiments are conducted using the D-optimal model to evaluate the cause-effect relationship and optimize the production process of instant tea powder. Four independent variables are selected for the survey namely alcohol concentration (40%; 50%; 60%), carrier mass (10 g; 20 g; 30 g), inlet air temperature (160 °C; 170 °C) and flow rate (4 rpm/min; 5 rpm/min). The instant tea powder is effectively created and met quality parameters, with a drying performance, moisture content, total phenol and flavonoid content of 29.15%, 4.83%, 45.29 mg GA/g, and 70.68 mg QE/g, respectively. In conclusion, the optimal parameters of the preparation process were identified, which included an alcohol content of 60%, a carrier mass of 10 g, an inlet air temperature of 165 °C, and a flow rate of 4 rpm/min.