Although they hold the promise of clean energy, state-of-the-art fuel cells based on polymer electrolyte membrane fuel cells are inoperable above 100°C, require cumbersome humidification systems, and suffer from fuel permeation. These difficulties all arise from the hydrated nature of the electrolyte. In contrast, “solid acids” exhibit anhydrous proton transport and high-temperature stability. We demonstrate continuous, stable power generation for both H 2 /O 2 and direct methanol fuel cells operated at ∼250°C using a humidity-stabilized solid acid CsH 2 PO 4 electrolyte.
The compound CsH2PO4 has emerged as a viable electrolyte for intermediate temperature (200–300 °C) fuel cells. In order to settle the question of the high temperature behavior of this material, conductivity measurements were performed by two-point AC impedance spectroscopy under humidified conditions (p[H2O] = 0.4 atm). A transition to a stable, high conductivity phase was observed at 230 °C, with the conductivity rising to a value of 2.2 × 10−2 S cm−1 at 240 °C and the activation energy of proton transport dropping to 0.42 eV. In the absence of active humidification, dehydration of CsH2PO4 does indeed occur, but, in contradiction to some suggestions in the literature, the dehydration process is not responsible for the high conductivity at this temperature. Electrochemical characterization by galvanostatic current interrupt (GCI) methods and three-point AC impedance spectroscopy (under uniform, humidified gases) of CsH2PO4 based fuel cells, in which a composite mixture of the electrolyte, Pt supported on carbon, Pt black and carbon black served as the electrodes, showed that the overpotential for hydrogen electrooxidation was virtually immeasurable. The overpotential for oxygen electroreduction, however, was found to be on the order of 100 mV at 100 mA cm−2. Thus, for fuel cells in which the supported electrolyte membrane was only 25 μm in thickness and in which a peak power density of 415 mW cm−2 was achieved, the majority of the overpotential was found to be due to the slow rate of oxygen electrocatalysis. While the much faster kinetics at the anode over those at the cathode are not surprising, the result indicates that enhancing power output beyond the present levels will require improving cathode properties rather than further lowering the electrolyte thickness. In addition to the characterization of the transport and electrochemical properties of CsH2PO4, a discussion of the entropy of the superprotonic transition and the implications for proton transport is presented.
6 September 2018 in Journal of Materials Chemistry A
A Y content of around 20 mol% and a Ba content approaching unity are essential for excellent sinterability, high ionic conductivity, and a high transport number of ionic conduction in Y-doped BaZrO3.
1 May 2005 in Electrochemical and Solid-State Letters
Solid-acid fuel cells (SCFCs) utilize an anhydrous, nonpolymeric proton conducting electrolyte that can operate at slightly elevated temperatures. By supporting thin electrolyte membranes (25-36 μm), on porous stainless steel gas-diffusion electrodes, SAFCs with peak power densities as high as were obtained. Cells were operated at with humidified supplied to the anode and humidified supplied to the cathode. Despite the thinness of the membranes, the open-circuit voltages were high, 0.91-1.01 V. These results transform SAFCs from laboratory curiosities into highly competitive energy conversion devices.
A process is demonstrated for the efficient separation of rare earth elements, using a combination of selective reduction and vacuum distillation of halides. The large differences in the redox chemistry of the rare earth elements and in the vapor pressures of rare earth di- and trihalides are exploited for separation. Experimental proof of concept is provided for the binary systems praseodymium-neodymium and neodymium-samarium. This process enhances the separation factor for the isolation of samarium and neodymium from their mixture by more than an order of magnitude.