SHINGO MIYAZAWA

Prof. Dr. SHINGO MIYAZAWA


Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
31 October 2019 in Infrastructures
Verified
Journal Article
Open access
PDF file
BZBernard Zulu
Bernard Zulu
SMSHINGO MIYAZAWA
SHINGO MIYAZAWA
NNNobukazu Nito
Nobukazu Nito
Accelerated curing is used for mass production in the precast concrete industry. Autogenous shrinkage and drying shrinkage occur in concrete, during and after accelerated curing. Thus, thermal cracks may occur in concrete due to both heating and cement hydration at early age, whereas drying shrinkage causes cracks after demolding. Ground granulated blast-furnace slag cement (GGBS), a byproduct in steel manufacture, has been used to improve concrete strength development during accelerated curing but poses a challenge of increased shrinkage. In this paper, two types of granulated blast-furnace slag cements were used to study mechanical and shrinkage properties of water cured and concrete subjected to accelerated curing. Limestone powder and gypsums, with two different types of fineness, were other additives used. An accelerated one day curing cycle was adopted that consisted of a 3 h delay period, heating to 65 °C, a peak temperature maintained for 3 h, and, finally, cooling. The results indicated that increment in gypsum fineness increased concrete expansion at one day for both sealed and accelerated cured concrete. In drying condition, similar shrinkage was observed. The addition of gypsum provided slightly lower shrinkage, and this may help to reduce cracking of concrete. Limestone powder improved concrete strength at early age. The difference in blast-furnace cement fineness did not have significant differences in compressive strengths, especially at 28 days.

8 June 2022 in Construction Materials
Verified
Journal Article
Open access
PDF file
Gerald GyabaahGerald Gyabaah
Gerald Gyabaah
SMSHINGO MIYAZAWA
SHINGO MIYAZAWA
NNNobukazu Nito
Nobukazu Nito
Usage of industrial by-products such as ground granulated blast furnace slag (GGBFS), gypsum, and limestone powder have gained prominence in concrete production. It is, therefore, very important to conduct research into the various materials and their attendant influence on properties of concrete at different ambient temperatures. This study focused on the slump, setting time, and compressive strength of concrete with GGBFS at a constant replacement ratio, in which different forms of gypsum, namely anhydrous and di-hydrate gypsum, were also added at different SO3 contents. Effect of addition of limestone powder was also investigated. The results of the tests indicated that both gypsum and limestone powder when added to a mix proportion containing GGBFS can improve slump and compressive strength of concrete. Anhydrous gypsum produced higher optimum compressive strength as compared with di-hydrate gypsum. An increase in SO3 content from gypsum contributed to strength development at early ages but reduced its long-term strength. Gypsum added to the mix delayed initial and final setting time. Limestone powder accelerated both initial and final setting times and contributed to increasing compressive strength after one day, thus three to seven days; however, the long-term strength was reduced. Curing temperature of concrete influenced strength development and the time required to remove formwork was determined for different mixtures using “maturity function”.

6 January 2025 in Infrastructures
Verified
Journal Article
Open access
PDF file
BKBenson KIPKEMBOI
Benson KIPKEMBOI
SMSHINGO MIYAZAWA
SHINGO MIYAZAWA
The application of self-compacting concrete in massive structures is still low due to the perceived high cracking tendency associated with high shrinkage and heat of cement hydration. This conclusion is from short-term research work of up to 3 months after casting. The purpose of this study is to evaluate the influence of drying shrinkage on the cracking resistance of massive self-compacting concrete with blast furnace slag using a three-dimensional finite element method of analysis (3D FEM). The restraint stress experiment results of the self-compacting concrete beam under drying conditions are compared with those of similar concrete beam models obtained from 3D FEM analysis. The value of the reduction coefficient for Young’s modulus of elasticity was proposed to consider the effect of stress relaxation due to creep in concrete. By using the proposed value of the reduction coefficient, thermal stress analysis was performed on a 1 m thick massive concrete wall member, and the cracking resistance of self-compacting concrete with different replacement ratios of blast furnace slag is discussed. By using the proposed reduction coefficient to evaluate concrete stress due to drying, the accuracy of thermal stress analysis results can be improved to a marginal error of ±15% from the experiment results. Also, the low-temperature rise caused by the high replacement ratio of blast furnace slag at 50% and 70%, respectively, contributed to improved cracking resistance. Furthermore, the optimum blast furnace slag replacement for better cracking resistance depends on the expected exposure condition of the structure.

30 October 2022 in Materials
Verified
Journal Article
Open access
PDF file
MHMINORU HATA
MINORU HATA
MSMakoto Sato
Makoto Sato
SMSHINGO MIYAZAWA
SHINGO MIYAZAWA
The purpose of this study was to apply a cementless binder using industrial by-products (fly ash, ground-granulated blast furnace slag, and silica fume) to precast concrete products. In this binder, calcium hydroxide was included as an alkali stimulant but Portland cement was not included. Experiments on the compressive strength and durability of this type of material were conducted and its applicability to precast concrete products was investigated using full-scale specimens. The experiments proved that high-temperature steam curing is effective at obtaining strength development and that compressive strength can be expressed as a linear function of the binder–water ratio. Experimental results of chloride ion diffusion coefficient and sulfuric acid resistance suggested that the proposed material has higher resistances than conventional cement concrete against these deterioration factors. It was also demonstrated that full-scale specimens of a box culvert and a centrifugally compacted pipe using this type of material have almost the same load-bearing capacity and deformation performance as those using conventional cement concrete. It is believed that the proposed material could be used as a construction material instead of cement concrete, contribute to reducing CO2 emission, and increase the reuse of industrial by-products.

3 July 2020 in Infrastructures
Verified
Journal Article
Open access
PDF file
BZBernard Zulu
Bernard Zulu
SMSHINGO MIYAZAWA
SHINGO MIYAZAWA
NNNobukazu Nito
Nobukazu Nito
Thermal stresses are generated in concrete during the accelerated curing process in precast concrete. These stresses may cause concrete to crack, which would have a negative effect on the general concrete performance. This paper provides the results of the thermal stress analysis of concrete containing 25% replacement of ordinary Portland cement (OPC) by ground granulated blast-furnace slag cement (GGBFS) with 3000 cm2/g fineness. A total of 2.5% of limestone powder and 1.75% of fine gypsum by mass of OPC were incorporated in the other concrete mix proportion to check their effect on the cracking tendency of concrete. The concrete was subjected to heat curing. JCMAC, a 3D finite element analysis software developed in Japan, was used in this study for the thermal stress analysis. The heat curing period of one day, similar to generally used in the precast concrete industry for civil engineering products consisting of 3 h preheating period, heating to a peak temperature of 65 °C and this temperature was kept for 3 h, and lastly cooling was used in the study. A standard precast box culvert model member together with some experimental results obtained in the laboratory were used in the analysis. Lower cracking resistance at 1 day was observed in both mix proportions that would lead to cracking at demolding time. Curing sheets were then introduced in the analysis to cover the precast mold during accelerated curing and this showed improvement in cracking resistance of concrete containing limestone powder and fine gypsum.

17 September 2015
Verified
Conference Paper
Closed access
HSH. Sato
H. Sato
SMSHINGO MIYAZAWA
SHINGO MIYAZAWA
AYA. Yatagai
A. Yatagai
Thermal stress in a gravity concrete dam was simulated by three dimensional FEM analyses taking autogenous shrinkage of concrete with full-sized aggregate into account. It is proved from experimental results that external concrete with blast-furnace slag Portland cement exhibits autogenous shrinkage of 130×10-6 at one year after casting, which is much larger than moderate-heat Portland cements with and without fly ash. Calculated thermal stress in upstream-downstream direction at the center of the concrete blocks near foundation rock is increased by autogenous shrinkage if concrete with large autogenous shrinkage is used. Thermal stresses in dam-axis direction at upstream and downstream surfaces are increased by the difference in autogenous shrinkage strains between internal and external concretes, if blast-furnace slag Portland cement is used. It can be said that autogenous shrinkage which simultaneously occurs with thermal strain should be taken into account in order to control thermal cracking during construction period which can adversely affect the stability, water tightness and durability of concrete gravity dams.