Cylindrical bodies in uniform flows can be coated with a porous medium as a passive flow and noise control method in an effort to reduce the acoustic effects of vortex shedding. To date, the employed open-cell porous materials typically possess a randomized internal structure. This paper presents the design and validation of a novel 3-D printed structured porous coated cylinder that has significant flexibility, in that the porosity and pores per inch of the porous coating can be modified independently and relatively easily. The performance of the structured porous coating design is compared against porous polyurethane and metal foam with the same coating dimensions and similar pores per inch and porosity via an experimental acoustic investigation, revealing strong similarity in the passive noise control performance of each material type. A numerical comparison illustrates the similarities of the wake structure of the 3-D printed porous coated cylinder to an equivalent Darcy–Forchheimer model simulation that represents a randomized internal porous structure. The performance similarities of these different porous material types indicate that a structured porous geometry can be used to understand the internal flow behavior of the porous medium responsible for reducing the cylinder vortex shedding tone that is otherwise extremely difficult or impossible with typical randomized porous structures. Moreover, significant potential exists for the porous structure to be further optimized or smartly tailored by architectural design for different control purposes, coating geometries and dimensions, and working conditions.

In this experimental study, the impact of symmetric local blowing on suppressing the vortex-induced noise of a circular cylinder was investigated. A highly instrumented cylinder with pressure taps and a series of blowing chambers was used to inject air along the span (seven times the cylinder diameter) at circumferential angles $\theta _{b}={\pm }41^{\circ }$ , ${\pm }90^{\circ }$ and ${\pm }131^{\circ }$ corresponding to the boundary layer, shear layers on the cylinder and separated shear layers, respectively. The investigation aimed to understand the noise reduction mechanism of local blowing by conducting near-field pressure and far-field noise measurements in synchronisation with flow field velocity measurements. Near-field pressure was measured around the circumference of the cylinder using a remote-sensing technique and planar particle image velocimetry was implemented to measure the velocity of the wake flow field at a diameter-based Reynolds number of $Re=7\times 10^{4}$ . The results revealed that the interaction of the rolling up separated shear layers, under the influence of high-momentum fluid travelling from the free stream to the wake, induced significant vertical flow movement in the vortex-formation region. This movement led to strong alternating surface pressure fluctuations at the cylinder's shoulders, contributing to the scattering of noise. It was demonstrated that local blowing delayed vortex shedding for all cases, except at $\theta _{b}={\pm }90^{\circ }$ , which elongated the shear layers and pushed the high-momentum transfer area farther downstream. The application of local blowing at $\theta _{b}={\pm }41^{\circ }$ was particularly effective in increasing the vortex formation size due to reduced entrainment of fluid-bearing vorticity.

Vortex shedding in the wake of a cylinder in uniform flow can be suppressed via the application of a porous coating; however, the suppression mechanism is not fully understood. The internal flow field of a porous coated cylinder (PCC) can provide a deeper understanding of how the flow within the porous medium affects the wake development. A structured PCC (SPCC) was three-dimensionally printed using a transparent material and tested in water tunnel facilities using flow visualisation and tomographic particle image velocimetry at outer-diameter Reynolds numbers of $Re = 7 \times 10^{3}$ and $7.3 \times 10^{4}$ , respectively. The internal and near-wall flow fields are analysed at the windward and mid-circumference regions. Flow stagnation is observed in the porous layer on the windward side and its boundary is shown to fluctuate with time in the outermost porous layer. This stagnation region generates a quasi-aerodynamic body that influences boundary layer development on the SPCC inner diameter, that separates into a shear layer within the porous medium. For the first time via experiment, spectral content within the separated shear layer reveals vortex shedding processes emanating through single pores at the outer diameter, providing strong evidence that SPCC vortex shedding originates from the inner diameter. Velocity fluctuations linked to this vortex shedding propagate through the porous layers into the external flow field at a velocity less than that of the free stream. The Strouhal number linked to this velocity accurately predicts the SPCC vortex shedding frequency.

The vortex shedding tone of a cylinder in uniform flow can be reduced by applying a porous coating yet this mechanism is not fully understood. An experimental investigation of asymmetric structured porous coated cylinders (SPCCs) was conducted in a small anechoic wind tunnel using a hot-wire anemometry probe placed in the boundary layer, separated shear layer and wake, in conjunction with a microphone in the far-field. Tests were conducted at Reynolds numbers 10⁵, $1.53\times {10}^5$ , and $1.66\times {10}^5$ . Each SPCC revealed a widened and deeper wake and reduced turbulent kinetic energy levels in the separated shear layer than the bare baseline cylinder. Furthermore, each SPCC revealed two tones that were a multiple of two apart in both the velocity and acoustic power spectral densities. It was shown that the higher frequency tone is generated by localized flow behaviors in the separated shear layer, independent of the vortex shedding tone and its magnitude is inversely related to the SPCC windward surface porosity. Applying a more densely spaced porous region on the cylinder windward side resulted in higher frequency broadband contributions that were shown to be independent of the velocity fluctuations in the wake region. Time-averaged velocity profiles in the wake revealed that the leeward side porosity strongly influences the drag coefficient. Linear stability analysis revealed that the SPCCs develop absolute instabilities in the near wake.

Large Eddy Simulation (LES) and Ffowcs Williams-Hawkings acoustic analogy are performed to study the effect of trailing-edge blowing on airfoil self-noise. Simulations were conducted using a National Advisory Committee for Aeronautics 0012 airfoil at zero angle of attack and a chord-based Reynolds number of $4\times {10}^5$ . The aerodynamic and aeroacoustic characteristics of the baseline airfoil were thoroughly verified by comparison with previous numerical and experimental data. The noise reduction effects of continuous and local blowing with different blowing ratios and blowing momentum coefficients were compared. A maximum noise reduction of 20 dB was achieved via trailing-edge blowing and the noise reduction mechanisms of the two blowing methods were discussed. The LES results show a pair of recirculation bubbles in the airfoil wake which are suppressed by trailing-edge blowing. As the blowing vortices convect into the wake, they stretch and stabilize the shear flows from airfoil surfaces. Instantaneous vorticity and root mean square velocity fluctuations are also weakened. There is a decrease in the spanwise coherence and an increase in the phase difference, which contribute to noise reduction. It is concluded that the suppression of turbulence fluctuations in the near wake is the main mechanism of noise reduction for airfoil trailing-edge blowing.