Quantification of interfacial tension (IFT) and contact angles is essential to characterize reservoir fluid-fluid and rock-fluid interactions. However, these measurements are highly dependent on chemical structure, surface residues, system conditions, flow dynamics and interface interactions. Interfacial interactions are specifically important for secondary and tertiary oil recovery processes where water or brine is injected to recover residual oil through complex multi-phase - rock/brine/oil- interactions Due to the delicate interactions across the interfaces, these systems are subjected to variations and inconsistencies that might be difficult to eliminate, thus, affecting the reliability, reproducibility, and certainty of the data. Therefore, reliable measurements need to eliminate fundamental sources of error and remove surface contaminants. To optimize these measurements, the presented methods take a holistic approach to carefully and reliably optimize the procedure for interfacial tension and contact angle measurements for fluid-fluid and rock-fluid interaction studies at ambient conditions (22.0 ± 2 °C and atmospheric pressure). •The presented method ensures minimization of impurities that alter interfacial tension measurements;•Enhanced preparation for tested surfaces for contact angle measurements, and;•Optimization of procedure at ambient conditions.
10 December 2018 in Oil & Gas Science and Technology – Revue d’IFP Energies nouvelles
We present a numerical validation of the scaling group presented by Schmid and Geiger ((2012) Water Resour. Res. 48, 3) for Spontaneous Imbibition (SI) through simulating a core sample bounded by the wetting fluid. We combine the results of the simulations with the semi-analytical model for counter-current spontaneous imbibition presented by Schmid et al. ((2011) Water Resour. Res. 47, 2) to validate the upscaling of laboratory experiments to field dimensions using dimensionless time. We then present a detailed parametric study on the effect of Boundary Conditions (BC) and characteristic length to compare imbibition assisted oil recovery with several types of boundary conditions. We demonstrate that oil recovery was the fastest and most efficient when all faces are open to flow. We also demonstrate that all cases scale with the non-dimensionless time suggested by Schmid and Geiger ((2012) Water Resour. Res. 48, 3) and show a close match to the numerical simulation and the semi-analytical solution. Moreover, we discuss how the effect of constructing a model with varying grid sizes and dimensions affects the accuracy of the results through comparing the results of the 2-D and 3-D models. We observe that the 3-D model proved superior in the accuracy of the results to simulate simple counter-current SI. However, we deduce that 2-D models yield satisfying enough results in a timely manner in the One End Open (OEO) and Two Ends Open (TEO) cases, compared to 3-D models which are time-consuming. We finally conclude that the non-dimensionless time of Schmid and Geiger ((2012) Water Resour. Res. 48, 3) works well with counter-current SI cases regardless of the boundary condition imposed on the core.
Petrographic observations are vital for carbonate pore‐typing, linking geological frameworks to petrophysical behavior. However, current petrographic pore typing is manual, with the qualitative to semi‐quantitative results not easily fitted into quantitative subsurface characterization. Some recent studies have automated this process using supervised machine learning (ML) and deep learning (DL), focusing on simple pore morphological features, and have reported high classification accuracies for several complex pore types. However, there are concerns about the validity of these studies due to conceptual and technical flaws in their collective approach. This study was aimed at a more fundamental problem, classifying between open microfractures and open pores in petrographic thin sections using an object‐based approach and explainable supervised ML. We analyzed 18 carbonate thin sections from the USA, numerically representing them using five shape features: compactness, aspect ratio, extent, solidity, and formfactor. Using a labeled data set of 400 microfractures and 400 pores, we evaluated nine of the most widely used supervised models. All models showed high testing accuracies (89.58%–90.42%). Interestingly, complex non‐linear models did not significantly outperform simpler linear ones. Compactness and aspect ratio were the most informative features. However, the labeled data sets did not reflect the overall data set's complexity, which suggested that high accuracies in similar studies might be due to curated data sets rather than accounting for the true complexity of carbonate pore systems. The study concludes that simple shape features are ineffective for classifying carbonate pore types. It is hoped that this study will provide a foundation for more robust artificial intelligence‐assisted pore typing.
20 June 2025 in International Journal of Multiphase Flow