A carrier-storage-enhanced superjunction (SJ) insulated gate bipolar transistor (CSE-SJ-IGBT) is proposed and investigated. In the CSE-SJ-IGBT, the p-pillar is connected to the Emitter via one diode or two series diodes, which helps to raise the hole quasi-Fermi potential of the p-pillar at the on-state so as to enhance the carrier-storage effect in the drift region (n-pillar and p-pillar) and reduce the on-state voltage ( ${V} _{\textbf {CE(sat)}}$ ). Moreover, the CSE-SJ-IGBT also can turn off rapidly as the conventional SJ-IGBT. Simulation results show that, under turn-off loss ( $\text{E}_{off}$ ) of 5 mJ/cm2, ${V} _{\textbf {CE(sat)}}$ of the 1.45-kV rated CSE-SJ-IGBT is as low as 1.07 V, which is 35% and 40% lower than that of the conventional SJ-IGBT and the field stop IGBT, respectively. Besides, the CSE-SJ-IGBT also offers large design freedom for obtaining excellent $\text{E}_{off}$ - ${V} _{\textbf {CE(sat)}}$ tradeoff.
1 December 2018 in Nuclear Instruments and Methods in Physics Research Section B: Beam Interactions with Materials and Atoms
The influence of a GaN layer as a sub-quantum well for an AlGaN/GaN/AlGaN double barrier resonant tunneling diode (RTD) on device performance has been investigated by means of numerical simulation. The introduction of the GaN layer as the sub-quantum well turns the dominant transport mechanism of RTD from the 3D-2D model to the 2D-2D model and increases the energy difference between tunneling energy levels. It can also lower the effective height of the emitter barrier. Consequently, the peak current and peak-to-valley current difference of RTD have been increased. The optimal GaN sub-quantum well parameters are found through analyzing the electrical performance, energy band, and transmission coefficient of RTD with different widths and depths of the GaN sub-quantum well. The most pronounced electrical parameters, a peak current density of 5800 KA/cm2, a peak-to-valley current difference of 1.466 A, and a peak-to-valley current ratio of 6.35, could be achieved by designing RTD with the active region structure of GaN/Al0.2Ga0.8 N/GaN/Al0.2Ga0.8 N (3 nm/1.5 nm/1.5 nm/1.5 nm).
3 February 2023 in IEEE Transactions on Electron Devices
This article proposes a novel five-contact vertical Hall device (VHD) with a buried layer (BL-5CVHD) compatible with a standard bipolar-CMOS-DMOS (BCD) process. VHDs sense a parallel magnetic field. Therefore, the transverse currents in the active region of VHDs determine the magnetic sensitivity. The BL provides a longitudinal electric field for majority carriers to form a transverse current, improving sensitivity. Through dedicated numerical simulations, we observe that the BL leads to a symmetrical distribution of the Hall potential, presenting better transverse currents. The geometric parameters of the BL-5CVHD are then further analyzed and optimized. Ultimately, the optimized BL-5CVHD voltage-related sensitivity reaches 10.53% $\text{T}^{-{1}}$ . Meanwhile, the offset voltage decreases to 0.55 mV.
23 April 2025 in IEEE Antennas and Wireless Propagation Letters
This letter introduces a circularly polarized (CP) filtering antenna that utilizes a substrate integrated waveguide (SIW) cavity to achieve wideband filtering characteristics. The antenna consists of a stacked patch, a radiating patch, a resonance excitation patch (REP), a SIW cavity, and four shorting pins. The stacked patch and the radiating patch together provide the CP performance. The REP is employed to excite the $\rm {TE}_{110}$ mode of the SIW cavity, thus realizing a filtering response. In addition, to suppress high-order modes that appear at higher frequencies, four shorting pins are embedded within the SIW structure, significantly suppressing unwanted radiation. Measured results indicate that an impedance bandwidth of 14.1% (23.5GHz to 27.1GHz), a 3dB axial ratio (AR) bandwidth of 10.9% (23.75GHz to 26.5GHz), and a peak gain of 6 dBi have been achieved. Thanks to the REP and SIW cavity, the proposed antenna shows excellent filtering performance. Featuring the merits of outstanding filtering response, stable and wideband CP radiation, easy integration, and low profile, the proposed antenna is promising for high-speed millimeter-wave applications.
This Letter presents an optimised cascaded integrator comb (CIC) filter sharpening algorithm embedding a fifth‐order finite impulse response filter, which improves the worst‐case alias rejection and simultaneously compensates the passband droop. The sharpening filter is designed without multipliers, which reduces hardware complexity. The results of a fourth‐order CIC filter design practice show that the proposed algorithm improves the worst‐case alias rejection to 128 dB, meanwhile the passband distortion is only 0.015 dB.