We investigate the magnetoresistance of ferrimagnetic GdFeCo across the magnetization compensation temperature . The magnetic field dependence of longitudinal resistivity () shows opposite trends below and above , and the variation of with becomes more significant as the temperature decreases. The observed unconventional magnetoresistance is attributed to the sperimagnetism of GdFeCo. Further investigations on the transverse resistivity () of GdFeCo unveils that, contrary to the recent reports that the transition metal dominates transport of rare-earth transition-metal ferrimagnets, the Gd contribution to magnetoresistance is comparable to the FeCo contribution, showing that the transport of GdFeCo is antiferromagnetic. Our results therefore show that ferrimagnets are a convenient platform for studying antiferromagnetic spin transport and also are potential materials that can enable antiferromagnetic spin devices.
Controlling impedance matching and enhancing absorption properties are crucial for developing next-generation microwave absorbing materials. Herein, we report the facile preparation of honeycomb-like core–shell nickel/copper silicate (Ni/CuSiO3) composite nanospheres with controlled shell (CuSiO3) thickness to control impedance matching and enhance absorption properties. The nanospheres with a shell thickness of about 30 nm had greatly improved microwave absorption performance. They exhibited a strong reflection loss of −39.5 dB (9.6 GHz) at the absorber thickness of 2.5 mm, with a wide effective absorbing bandwidth of 4.8 GHz (7.8–12.6 GHz). This remarkable microwave absorption performance is attributed to a novel structure that enhanced interfacial polarization and controlled shell thickness, resulting in good impedance matching of electromagnetic properties (ε, μ) and magnetic loss. Our permittivity-controlled core–shell Ni/CuSiO3 composite nanospheres could be used to fabricate novel high-performance microwave absorbers.
22 December 2023 in Journal of Materials Chemistry A
Triboelectric nanogenerators (TENGs) have predominantly relied on non-degradable polymers for their development, raising concerns about their environmental impact upon disposal. In response, the exploration of alternative paths for TENG fabrication using environmentally friendly materials has gained attention. However, the performance of TENGs fabricated using degradable alternatives has fallen short when compared to devices fabricated using their non-degradable counterparts. To bridge this performance gap, our study focuses on optimizing the key factors influencing TENG efficiency. We systematically investigated nanofiber structures, introduced chemical surface modifications, and tailored triboelectric properties through the integration of ferroelectric molecules and composite structures. By strategically combining PEI(b)-modified CA nanofibers as the tribo-positive layer and gelatin-based nanofibers embedded with ImClO4 and MXene fillers as the tribo-negative layer, we have elevated the output performance of TENGs to a level comparable to those based on non-degradable polymers. Specifically, our degradable TENGs demonstrated an open-circuit voltage of up to 300 V, a short-circuit current of 10 μA cm−2, and an impressive maximum power density exceeding 500 μW cm−2. These findings mark a significant advancement in output performance compared to other TENGs employing degradable materials. Furthermore, the degradation experiment revealed that the TENGs used in this study can degrade almost completely within approximately 60 days when exposed to natural environmental conditions.
Nanocomposite structures, where the Fe, Fe2O3, or Ni2O3 nanoparticles with thin carbon layers are distributed among a single-wall carbon nanotube (SWCNT) network, are architectured using the co-arc discharge method. A synergistic effect between the nanoparticles and SWCNT is achieved with the composite structures, leading to the enhanced sensing response in ammonia detection. Thorough studies about the correlation between the electric properties and sensing performance confirm the independent operation of the receptor and transducer in the sensor structure by nanoparticles and SWCNT, respectively. Nanoparticles with a large specific surface area provide adsorption sites for the NH3 gas molecules, whereas hole carriers are supplied by the SWCNT to complete the chemisorption process. A new chemo-resistive sensor concept and its operating mechanism is proposed in our work. Furthermore, the separated receptor and transducer sensor scheme allows us more freedom in the design of sensor materials and structures, thereby enabling the design of high-performance gas sensors.