The combined connection with welds and bolds can be widely used in reinforcing the joint in steel structure. In this paper, proposed design method of combined connection with bolts and longitudinal welds was given based on the tests and finite element analysis (FEA). The method considers the effect of the strength ratio between bolts and welds. The safety and reliability of the method were verified by FEA and comparison with other design method. The design method can contribute to the promotion of the application of the combined connections.
1 December 2019 in IOP Conference Series: Materials Science and Engineering
For the problem of frequency operation and the saturation of control input of the controller which caused by the unpredictable load disturbance of propulsion system, the active disturbance rejection control (ADRC) with dead zone and saturation disturbance compensation is designed. The dead zone and anti-saturation disturbance compensation module are introduced into the observer to reduce the operating frequency of the propulsion control system under load disturbance and to improve the control performance when the control input is saturated. However, the error feedback part of ADRC uses the finite-time sliding mode feedback. Simulation results show that the proposed algorithm reduces the operating frequency of the control system and improves the control performance when the control input is saturated.
22 February 2020 in Mathematical Problems in Engineering
In this paper, in order to handle the nonlinear system and the sophisticated disturbance in the marine engine, a finite-time convergence control method is proposed for the diesel engine rotating speed control. First, the mean value model is established for the diesel engine, which can represent response of engine fuel injection to engine speed. Then, in order to deal with parameter perturbation and load disturbance of the marine diesel engine, a finite-time convergence active disturbance rejection control (ADRC) is proposed. At the last, simulation experiments are conducted to verify the effectiveness of the proposed controller under the different load disturbances for the 7RT-Flex60C marine diesel engine. The simulation results demonstrate that the proposed control scheme has better control effect and stronger anti-interference ability than the linear ADRC.
A system combining gas-phase oxidation and liquid-phase collision absorption for removing NO from marine diesel engine exhaust was proposed. This method was the first to utilize different physical states of the same mixed solution to achieve both pre-oxidation and impingement reduction absorption of exhaust gases. During the pre-oxidation stage, a mixture of (NH4)2S2O8 and urea solution was atomized into a spray using an ultrasonic nebulizer to increase the contact area between the oxidant and the exhaust gas, thereby efficiently pre-oxidizing the exhaust gas in the gas phase. In the liquid-phase absorption stage, the (NH4)2S2O8 and urea solution was used in an impingement absorption process, which not only enhanced gas–liquid mass transfer efficiency but also effectively inhibited the formation of nitrates. Experimental results showed that, without increasing the amount of absorbent used, the maximum NO removal efficiency of this method reached 97% (temperature, 343 K; (NH4)2S2O8 concentration, 0.1 mol/L; urea concentration, 1.5 mol/L; NO concentration, 1000 ppm; pH, 7; impinging stream velocity, 15 m/s), compared to 72% using the conventional liquid-phase oxidation absorption method. Additionally, this method required only the addition of a nebulizer and two opposing nozzles to the existing desulfurization tower to achieve simultaneous removal of sulfur and nitrogen oxides from the exhaust gas, with low retrofitting costs making it favorable for practical engineering applications.
Wartsila RT-flex 60C diesel engine is selected as the object to research pressure control of fuel common rail system, building the system simulation model, and analyzing main factors influencing rail pressure in the system. it was concluded that they were diesel engine speed, load. In the process of MATLAB/Simulink simulation, the rail pressure control logic was designed by adopting maps with the two factors as independent variables to get theory feedforward quantity of fuel rack, feedback quantity of fuel rack is obtained by fuzzy PID control. The simulation experiments show that the improved control method reduces the rail pressure fluctuation, at the same time the overshoot volume of dynamic rail pressure control is greatly reduced, response velocity quickened. The control method has been used in a Marine simulator.
Marine main engines commonly operate at low speed and low load to achieve economical cruising, which lowers the exhaust temperature. Developing catalysts for the selective catalytic reduction of NO with ammonia (NH3–SCR) that are active at low temperature and over a wide temperature window is therefore essential. In this work, multiphase heterojunction CuO/CuFe2O4 spinel catalysts were synthesized by a microwave-assisted hydrothermal method. Performance testing showed that the CF-MW-5 catalyst (Cu:Fe = 1.07:2, 5 min of microwave treatment) gave the best performance. Notably, in a continuous 60 h test at 230 °C that included 33 h under 200 ppm of SO2 and 5 vol % H2O, its NO removal efficiency never fell below 86%. Comprehensive characterization showed that the microwave-assisted synthesis was accompanied by partial reduction of Cu2+ and Fe3+ ions and by enrichment of the surface in adsorbed-oxygen and vacancy-related species, providing abundant active sites for the SCR reaction. Crucially, a structure–activity analysis shows that the catalytic activity scales neither with the total surface acidity nor with the total active-oxygen fraction─both of which increase monotonically with irradiation time─nor with the surface area, but instead follows a volcano-type relationship that closely mirrors the surface Cu+/Fe2+ redox-couple density and the population of low-temperature (weak) acid sites. After normalizing the apparent rate constants to unit surface area, CF-MW-5 still exceeds the untreated sample by a factor of 1.69, showing this improvement to be intrinsic rather than merely textural. We propose that these coupled Cu+/Fe2+ sites sustain the redox cycle while acting as Lewis acid centers that govern low-temperature NH3 activation, together rationalizing the wide operating window; the elementary reaction pathway is offered as a hypothesis consistent with these data rather than as an established mechanism. This work therefore moves beyond synthesis optimization to establish which surface descriptors do, and which do not, control low-temperature NH3–SCR over microwave-engineered spinel catalysts.