Hybrid AC-DC microgrids (HMG) have become more popular recently because of their superior features in comparison with pure AC and DC microgrids (MGs). HMGs have fewer power converters and are more flexible than pure AC and DC MGs, but the number of converters in HMG is still significant, especially when the DC part of HMG has several voltage levels. A new simplified and more flexible architecture for HMGs that features a new multi-port interlinking converter (IC) is proposed in this paper. Using the proposed IC, the number of power electronic converters in an HMG with several DC bus voltages can be reduced without increasing the number of active switches in the IC or the complexity of its control system. In this paper, the new simplified HMG architecture is presented and the operation of the proposed IC as a single unit and as a part of a simplified HMG are explained, along with its features. Experimental results obtained from a scaled-down prototype are also presented to confirm the feasibility of the multi-port interlinking converter. Simulation results that show the effect of load variations in the IBA DC bus on the operation of the HMG are also presented as well.
12 June 2019 in IEEE Transactions on Power Electronics
A new single stage three-phase AC-DC converter with four switches and galvanic isolation is proposed in this paper. The new converter is simple and uses fewer switches than previously proposed AC-DC converters of the same type. It is a bridgeless converter that can operate with continuous input current and with any PWM method suitable for a standard three-phase six-switch voltage source rectifier. In this paper, the operation, control, analysis and design of the proposed converter are explained and its features are discussed. Experimental results obtained from a prototype that confirm the feasibility of the converter are presented as well.
The paper proposes a novel interleaved AC-DC ZCS-PWM boost converter that requires the use of just a single active auxiliary switch to assist in the turning off the main power circuit switches with ZCS. The auxiliary switch can be turned on and off with ZCS and its auxiliary circuit allows the converter to operate without an increase in the main switch peak current or voltage stress. The auxiliary switch in the converter is active for a much shorter time than in most other ZCS-PWM converter, which allows the converter to operate at higher power levels than other previously proposed interleaved ZCS-PWM converter with a single auxiliary switch. The proposed converter’s operation is explained in the paper and its key features and design considerations are discussed. Experimental results that confirm the operation of the proposed converter are presented as well.
3 June 2019 in IEEE Transactions on Power Electronics
In this letter, the use of three-level (TL), zerovoltage-zero-current switching (ZVZCS) converters is investigated as a way of improving light-load efficiency in fullbridge converters with MOSFETS. The general operation of an example TL-ZVZCS full-bridge converter is briefly explained and the basic principles as to how it can how improve light-load efficiency are discussed. Experimental results that compare the efficiency of a prototype of the example TL-ZVZCS converter to that of the conventional ZVS-PWM full-bridge are presented to confirm the superior light-load efficiency of TL-ZVZCS converters.
DC microgrids (DC-MGs) are recognized as an efficient alternative for common AC-MGs. DC-MGs need fewer power electronic converters since most of distributed generation (DG) units and electronic loads operate with DC voltage. The integration of DGs that generate AC voltage, such as wind energy conversion systems (WECSs) into DC-MGs, however, requires an AC-DC conversion unit to perform AC-DC conversion and galvanic isolation and to control the WECS. Typically, two separate cascaded converters are used to perform such functions, which increases the cost and size of DC-MGs. In this paper, an isolated single-stage AC-DC converter is proposed that is able to perform all the required function of a WECS AC-DC conversion unit, to overcome the drawbacks of the two-converter structure. First, the operation of the proposed converter and its features as a single unit are described. The operation of the WECS with the proposed converter is then studied. A design procedure for both the steady-state and dynamic operation of the converter is developed based on a mathematical model. Experimental results obtained from a scaled-down prototype converter are also presented to confirm the feasibility of the proposed converter as a single unit. The complete WECS operation is verified by the simulation results of the aerodynamic, mechanical, and electrical system models, using MATLAB/SIMULINK.
22 July 2020 in IEEE Open Journal of Power Electronics
The ZVS-T-type converter can be used as an alternative to the conventional ZVS-PWM-FB converter for applications where improved light-load operation is required. In this converter, two of the switches conduct only freewheeling mode currents and two of the switches conduct energy-transfer mode currents. This is unlike the switches in the ZVS-PWM-FB converter that must conduct both currents. Although the ZVS-T-type converter needs a lower amount of inductive energy to achieve ZVS in its switches, it has a higher primary current during its freewheeling modes than the ZVS-PWM-FB converter because it is a half-bridge converter. In this paper, the use of ZVZCS methods to reduce the RMS current in switches that are used in the freewheeling current path is investigated. The operation of the ZVS-PWM-T-type converter and a ZVZCS-T-type converter are reviewed and compared analytically. Experimental results obtained from prototypes of the two converters along with the results from prototypes of the standard ZVS-PWM-FB and ZVZCS-PWM-FB converters are presented. It is demonstrated that a ZVZCS-T-type converter has a better light-load efficiency than the ZVS-PWM-FB and the ZVS-T-type converters and the current stress in its middle-leg switches is much smaller; thus, it can be implemented with much smaller and inexpensive middle-leg switches.