Temperature‐sensitive (thermosensitive) hydrogels, which are part of the family of stimulus‐sensitive hydrogels, consist of water‐filled polymer networks that display a temperature‐dependent degree of swelling. Thermosensitive hydrogels, which can undergo phase transition or swell/de‐swell as temperature changes, have great potential in various technological and biomedical purposes for a number of reasons: their temperature response is reversible, hydrogels are stable and easy to prepare, they can be biocompatible and also be suitably combined with other organic and inorganic materials, resulting in new materials with outstanding properties. Among thermosensitive hydrogels poly(N‐isopropylacrylamide) (PNIPAAm) is the most extensively studied because it brings together the best properties of these materials. Consequently, in the past few years, a wide number of applications and new chemical processes to prepare PNIPAAm and their derivatives are being proposed. The objective of this review is to summarize the fundamentals of thermosensitive hydrogels and recent advances in preparation and both technological and biomedical applications of thermosensitive hydrogel, with a special focus on PNIPAAm and their derivatives. Special attention has been given to the discussion of challenges and future research perspectives based on new horizons not yet considered.
Recently, electro-Fenton (EF) process has been shown as a promising, facile, effective, low cost and environmentally-friendly alternative for synthesizing polymer nanogels suitable as biocompatible nanocarriers for emerging biomedical applications. Here, the electrochemically-assisted modification of poly(vinylpyrrolidone) (PVP) by EF process was studied to assess the role of key operation parameters for a precise modulation of polymer crosslinking and its functionalization with [sbnd]COOH and succinimide groups. The dimensions of the nanogels, in terms of hydrodynamic radius (Rh) and weight-average molecular weight (Mw), can be tuned up by controlling the electrolysis time, current density (j) and PVP and Fe2+concentrations, as demonstrated via dynamic and static light scattering and gel permeation chromatography analysis. Using PVP at 0.25 wt.%, Fe2+at 0.5-1.0 mmol dmâ\u88\u923and low j, short treatment times induced intramolecular crosslinking with chain scission, allowing size reduction of PVP particles from 24 to 9â\u80\u9310 nm. Longer reaction times and higher PVP and Fe2+contents favored intermolecular crosslinking ending in Mwvalues higher than the initial 3.95 Ã\u97 105 g molâ\u88\u921. An excessive [rad]OH dose from a too high circulated charge (Q), i.e., too prolonged electrolysis time even at low j or too high j even for short time, promoted intramolecular crosslinking (Rh â\u88¼Â 10â\u80\u9312 nm) along with a very significant chain scission probably owing to the loss of mobility of the three-dimensional nanogel network. In conclusion, EF allowed transforming the architecture of linear, inert PVP chains into a functionalized nanogel with [sbnd]COOH and succinimide groups that have great potential for further conjugation
5 January 2018 in The Journal of Physical Chemistry C
Flexible and lightweight electrodes are prepared using a two-step process. First, poly(3,4-ethylenedioxythiophene) (PEDOT) microparticles are loaded into poly-γ-glutamic acid (γ-PGA) hydrogel matrix, during the reaction of the biopolymer chains with the cross-linker, cystamine. After this, PEDOT particles dispersed inside the hydrogel are used as polymerization nuclei for the chronoamperometric synthesis of poly(hydroxymethyl-3,4-ethylenedioxythiophene) (PHMeDOT) in aqueous solution. After characterization of the resulting electrode composites, electrochemical studies revealed that the capacitive properties drastically depend on the polymerization time used to produce PHMeDOT inside the loaded hydrogel matrix. Specifically, flexible electrodes obtained using a polymerization time of 7 hours exhibit an specific capacitance of 45.4±0.7 mF/cm2 from cyclic voltammetry and charge-discharge long-term stability. The applicability of these electrodes in lightweight and flexible energy-harvesting systems useful for energy-autonomous, low-power, disposable electronic devices, has been proved powering a LED bulb.
Herein, a versatile bilayer system, composed by a polypropylene (PP) mesh and a covalently bonded poly(N-isopropylacrylamide) (PNIPAAm) hydrogel, is reported. The cell adhesion mechanism was successfully modulated by controlling the architecture of the hydrogel in terms of duration of PNIPAAm grafting time, crosslinker content, and temperature of material exposure in PBS solutions (below and above the LCST of PNIPAAm). The best in vitro results with fibroblast (COS-1) and epithelial (MCF-7) cells was obtained with a mesh modified with a porous iPP-g-PNIPAAm bilayer system, prepared via PNIPAAm grafting for 2 h at the lowest N,N′-methylene bis(acrylamide) (MBA) concentration (1 mM). Under these conditions, the detachment of the fibroblast-like cells was 50% lower than that of the control, after 7 days of cell incubation, which represents a high de-adhesion of cells in a short period. Moreover, the whole system showed excellent stability in dry or wet media, proving that the thermosensitive hydrogel was well adhered to the polymer surface, after PP fibre activation by cold plasma. This study provides new insights on the development of anti-adherent meshes for abdominal hernia repair.