C 60 fullerene exhibits unique optical properties that have high potential for wide photo-optical applications. To analyze the optical properties of C 60 , its excitation and emission properties were studied using UV-Vis absorption and photoluminescence (PL) spectroscopy, which were performed in various, non-polar organic solvents such as toluene, xylene, and trichloroethylene (TCE). The C 60 solutions in toluene, xylene, and TCE displayed similar excitation bands at 625, 591, 570, 535, and 404 nm corresponding to
A
g →
T
1u and
A
g →
T
1g transitions. However, these bands differed from the solid C 60 observed by UV-Vis diffuse reflectance spectroscopy. The two emission band energies of C 60 solution in toluene and xylene were nearly the same (1.78 and 1.69 eV), whereas the C 60 solution in TCE was shifted to 1.72 and 1.65 eV. Because the polarity of TCE is higher than that of toluene and xylene, the PL spectrum of the C 60 solution in TCE was red-shifted. The PL spectroscopy had a better capability than UV-Vis absorbance spectroscopy to distinguish the different interactions between C 60 and the organic solvents due to their different solvent polarities.
Textversion:authorThe graphite encapsulated iron nanoparticles were fabricated by using arc discharge method. The synthesized nanoparticles were pre-treated by an inductively-coupled RF Ar plasma and then post-treated by NH3 plasma under various gas pressures and treatment times. Analyses of XPS spectra have been carried out to study the effect of the plasma treatment on the surface modification of nitrogen-containing groups. The morphological changes of the particles surface by plasma treatment have also been analyzed by using HR-TEM. Present results show that the highest values of N/C atomic ratio of 5.4% is obtained by applying 10 min of Ar plasma pre-treatment and 2 min of NH3 plasma post-treatment conducted in RF power of 80 W and gas pressure of 50 Pa
In this study, composite materials consisting in HKUST-1 [Cu3(BTC)2] (BTC: benzene 1, 3, 5-tricarboxylate) and an Indonesian activated natural zeolite (ANZ) from Klaten, Central Java, were successfully prepared and characterized. The purpose of this research was to determine the effect of the combination of these two materials on the characteristics of the composite as well as to determine its CO2 gas adsorption ability. The composite HKUST-1-ANZ (ANZ@HKUST-1) was synthesized in two different techniques, i.e., solvothermal and sonication method. The obtained materials exhibited X-ray diffractogram characteristics of both HKUST-1 and ANZ. Fourier-transform infrared (FTIR) analysis showed a combination of peaks from HKUST-1 and ANZ, i.e. peaks assigned to carboxylate groups and bonds between Cu-O from HKUST-1, as well as N-H bending and SiO from ANZ. The addition of ANZ to HKUST-1 decreased its surface area and nitrogen sorption capacity. Application of the composites as CO2 capture materials shows their CO2 adsorption capacity is increased (ca. 12%) comparing to the initial materials.
TiO2/SBA-15 photocatalysts were successfully prepared by impregnating low loading titania to SBA-15 via slow calcination. The photocatalyst is efficient for fast methylene blue removal via adsorption and photodegradation methods. The impregnation of low TiO2 loading via slow calcination enhanced TiO2 dispersion that preserved the SBA-15 porosity and uniform morphology. High interfacial interaction of TiO2/SBA-15 improves TiO2 photoresponse by narrowing the bandgap, resulting in a stronger redox ability. The methylene blue removal on 10%TiO2/SBA-15 followed the pseudo-second-order kinetic model that reached 67% removal efficiency in 90 min. The synergy between adsorption and photodegradation is responsible for the fast methylene blue removal. These results indicate the importance of maintaining the adsorption capacity in SBA-15 after impregnation with TiO2 for efficient adsorption-photodegradation processes, which can be achieved by controlling the deposition of TiO2 on SBA-15. A low titania loading further reduced the cost of photocatalysts, thus becoming a potential material for environmental pollution treatment.
Recently, there has been considerable attention in the development of biodegradable plastic. Our current use and disposal of synthetic-based conventional plastics caused high rates of land-fill problems because of its persistence in the environment. Many renewable resources have been used as a source of starch and cellulose as bioplastic constituents. One of the most available biomasses that have not been explored is water hyacinth (Eichornia crassipes). In the present study, we investigated the fabrication of biodegradable plastic made with a matrix of 3% and 5% mixture of starch and cellulose extracted from water hyacinth in different weight ratios of 10:0, 9:1, 8:2, and 7:3. The addition of water hyacinth cellulose was purposed as a reinforcing agent to improve the performances of the starch bioplastics. Chitosan with a matrix of 1% was also added to improve the mechanical function of starch bioplastic. There were two main steps performed to isolate water hyacinth cellulose, i.e., bleaching and alkali treatment. The chemical and physical characteristics of starch-based bioplastics and their composites were then analyzed by Fourier transform infrared (FTIR) spectroscopy and scanning electron microscopy (SEM). Moreover, the tensile strength and bioplastic degradation tests were also conducted to study the performance and biodegradability. The FTIR data shows that the functional group’s absorption revealed corresponds to the pure cellulose indicating the successful cellulose isolation from water hyacinth. The tensile strength of bioplastic starch- chitosan increases with the addition of water hyacinth cellulose. The improvement of the physical properties of bioplastic starch was achieved through the addition of chitosan and water hyacinth. The mixture of starch-chitosan combined with water hyacinth cellulose produces environmentally friendly bioplastics shown by the increased mechanical and physical properties compared to starch-alone bioplastic.