The induction motor is by far the most used motor type in the industry due to its low cost, robustness, and line-start ability. However, different alternatives to induction motors have been investigated in recent years because of global warming concerns, demands for energy saving, and meeting the new international efficiency (IE) standards. One suitable candidate for fan and pump applications is the line-start synchronous reluctance motor (LS-SynRM). In these applications, the moment of inertia of the load is relatively low and does not have a destructive effect on the synchronization capability of LS-SynRM. In line-start applications, the value of the power factor has great importance. Ferrite magnets could be used in the structure of an LS-SynRM to improve its power factor. The resulting motor is a line-start permanent magnet assisted synchronous reluctance motor (LS-PMaSynRM). In this article, a novel LS-PMaSynRM for fan application is presented considering a benchmark three-phase 400W–1400 rpm induction motor. It is verified that the proposed motor can reach higher efficiency classes than the benchmark induction motor for the same output power by prototype test. Two LS-PMaSynRMs considering copper and aluminum as conductive materials for the rotor core are prototyped, and performance results have been presented.
17 February 2022 in COMPEL - The international journal for computation and mathematics in electrical and electronic engineering
This paper aims to present an adaptive method based on finite element analysis to calculate iron losses in switched reluctance motors (SRMs). Calculation of iron losses by analytical formulas has limited accuracy. On the other hand, its estimation in rotating electrical machines through fully dynamic simulations with a fine time-step is time-consuming. However, in the initial design process, a quick and sufficiently accurate method, i.e. a value close to that of iron losses, is always welcome. The method presented in this paper is a semi-analytical approach. The main problem is that iron losses depend on d B/d t. Therefore, the accuracy of the calculation of iron losses depends on the accuracy of the calculation of the first derivative of the flux density waveform. When adopting a magnetostatic model to estimate the iron losses, an important question arises: by how many magnetostatic simulations can the iron losses be estimated within the desired accuracy? In the proposed algorithm, the aim is not to accurately calculate the value of iron losses in SRMs. The objective is to find a numerical error criterion to calculate iron losses in SRMs with a minimum number of magnetostatic simulations. A finite element solver is developed by authors in MATLAB to solve the 2 D nonlinear magnetostatic problem using the Newton–Raphson method. A parametric program is developed to create geometry and mesh. The proposed method is implemented in MATLAB using the developed solver. Counterpart simulations are done in the ANSYS Maxwell software to validate the accuracy of the results generated by the developed solver. The performance of the proposed method is studied on a 12/8 (500 W) SRM. Three scenarios are studied. The first one is the calculation of iron losses by uniform refinement, and the second one is by adaptive refinement, and the last one is by adaptive refinement started by particular initial points (switching points). According to the results, the proposed method substantially reduces the number of magnetostatic simulations without sacrificing accuracy. The main novelty of this paper is introducing an error criterion to find the minimum number of magnetostatic simulations that are needed to calculate iron losses with the desired accuracy.
30 September 2022 in COMPEL - The international journal for computation and mathematics in electrical and electronic engineering
Rotor shape optimization is crucial in designing synchronous reluctance machines (SynRMs) because the machine performance is directly proportional to the rotor’s magnetic saliency ratio. The rotor geometry in synchronous reluctance machines is complex, and many geometrical parameters must be optimized. When fluid flux-barrier geometry is desirable, using analytic equations to prepare the rotor geometry for finite element analysis could be tedious. This paper aims to provide a robust numerical procedure to draw the fluid flux-barrier geometry in transversally laminated radial flux inner and outer rotor SynRMs by directly solving the magnetic vector potential equation using the finite difference method.. In this paper, the goal is to have a robust procedure for drawing the rotor geometry for an arbitrary number of slots (Ns), poles (p) and flux-barrier layers (Nfb). Therefore, this paper targeted several combinations to investigate the performance of the proposed algorithm. The MATLAB software is used to implement the proposed algorithm. The ANSYS Maxwell software is used for counterpart finite element simulation to check the correctness of the results derived by the proposed method. Several inner and outer rotor SynRMs considering a different number of poles and a different number of flux-barrier layers per pole are studied to investigate the performance of the proposed algorithm. Results corresponding to each case are presented, and it is shown that the method is robust, flexible and fast enough, which could be used for the generation of the rotor geometry for the finite element analysis effectively. The value of the proposed algorithm is its simplicity and straightforwardness in its implementation for the preparation of the rotor geometry with the desired fluid flux-barrier layer curvature resolution suitable for the finite element analysis. The procedure presented in this paper is based on the ideal magnetic loading concept, and in future works, a similar idea could be used for linear and axial flux SynRMs.
Wave and tidal energies are some of the most prominent potential sources of renewable energy. Presently, these energy sources are not being utilized to their maximum extent. In this paper, we present a new conversion mechanism with an innovative electrical energy converter design that enables the use of wave energy to its maximum potential. The conventional wave energy converter comprises two stages of conversion (kinetic to mechanical and mechanical to electrical), imposing transformation loss that reduces the overall system efficiency. Additionally, the architecture and operational norms are dependent on the availability of shoreline areas, and the convertor is not suitable for all ocean weather conditions. To solve these problems, we have developed a wave energy conversion system that integrates the two stages of power with the minimum number of moving parts. This results in significant reduction of transformation losses that otherwise occur in the process. This paper presents an innovative idea of designing a DC generator that reduces the hierarchy of power conversion levels involved to improve the efficiency. The back and forth motion of the machine means it operates in a two-quadrant generation mode. The machine was constructed as a square box model with windings placed on both the top and bottom stator plates, and the rotor consisted of a field winding placed between these plates with two axes of operation. The electromagnetic field (EMF) induced in the stator plates is due to the resulting flux cutting, which is generated by a rolling object (rotor) in between them. A finite element analysis (FEA) of the machine is also listed to validate the flux linkage and operational efficiency. Additionally, a generator is fabricated to the predetermined design criteria as a proof of concept and the corresponding results are posted in the paper. Additionally, we present the material and cost limitations of this invention and outline some possible future directions.
5 August 2026 in e-Prime – Nexus of Electrical, Electronic, and Intelligent Engineering