Robert Dagle

Robert Dagle


Research Focus & Metrics

Academic Career Length

15Years (2012-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
18 June 2012 in Catalysis Science & Technology
Verified
Journal Article
Closed access
PDF file
VLVanessa M. Lebarbier
Vanessa M. Lebarbier
RDRobert Dagle
Robert Dagle
LKLibor Kovarik
Libor Kovarik
JLJair A. Lizarazo-Adarme
Jair A. Lizarazo-Adarme
DKDavid L. King
David L. King
DPDaniel R. Palo
Daniel R. Palo
A Pd/ZnO/Al2O3 catalyst was developed for the synthesis of methanol and dimethyl ether (DME) from syngas with temperatures of operation ranging from 250 °C to 380 °C. High temperatures (e.g. 380 °C) are of interest when combining methanol and DME synthesis with a methanol to gasoline (MTG) process in a single reactor bed. A commercial Cu/ZnO/Al2O3 catalyst, utilized industrially for the synthesis of methanol at 220–280 °C, suffers from a rapid deactivation when the reaction is conducted at high temperature (> 320 °C). On the contrary, a Pd/ZnO/Al2O3 catalyst was found to be highly stable for methanol and DME synthesis at 375 °C. The Pd/ZnO/Al2O3 catalyst was thus further investigated for methanol and DME synthesis at P = 34–69 bar, T = 250–380 °C, GHSV = 5000–18 000 h−1, and molar feeds H2/CO = 1, 2, and 3. Selectivity to DME increased with decreasing operating temperature, and increasing operating pressure. Higher space velocity and H2/CO syngas feed ratios also enhanced DME selectivity. Undesirable CH4 formation was observed, however, it could be lessen through choice of process conditions and by catalyst design. By studying the effect of the Pd loading and the Pd : Zn molar ratio the formulation of the Pd/ZnO/Al2O3 catalyst was optimized. A catalyst with 5% Pd and a Pd : Zn molar ratio of 0.25 : 1 has been identified as the preferred catalyst. Results indicate that PdZn particles are more active than Pdo particles for the synthesis of methanol and less active for CH4 formation. A correlation between DME selectivity and concentration of acid sites has been established. Hence, two types of sites are required for the direct conversion of syngas to DME: (1) PdZn particles are active for the synthesis of methanol from syngas, and (2) acid sites which are active for the conversion of methanol to DME. Additionally, CO2 formation was problematic as PdZn was found to be active for the water-gas-shift (WGS) reaction, under all the conditions evaluated.

5 February 2019 in Catalysis Science & Technology
Verified
Journal Article
Closed access
PDF file
JSJohnny Saavedra
Johnny Saavedra
RDRobert Dagle
Robert Dagle
VDVanessa Lebarbier Dagle
Vanessa Lebarbier Dagle
CSColin Smith
Colin Smith
KAKarl O. Albrecht
Karl O. Albrecht
In this paper, we report on solid acid catalysts and process conditions suitable for oligomerization of ethanol-derived mixed olefins propene and isobutene to transportation fuels, specifically targeting high-octane gasoline or jet-range hydrocarbons with high carbon efficiency. Catalytic performance was evaluated for two classes of solid acid catalysts—zeolites (H-ZSM-5, H-Y, H-beta) and polymeric resins (Amberlyst-36, Purolite-CT275)—each of which offer different catalytic properties. Two representative model olefin feeds: 1) diisobutene and 2) isobutene/propene (4/1 mol) mixture were used. Interestingly, both classes of solid acid catalysts can be tuned to produce a similar jet-distillate range hydrocarbon product with temperature determined to be the critical operating process parameter. For example, the propene conversion over H-beta zeolite was dramatically increased from 7 to 87% when the temperature was increased from 140 to 200 °C; whereas, nearly all (>99%) of the isobutene was converted over the same temperature range. However, with this relatively modest temperature increment (60 °C), formation of products in the jet-distillate range dramatically decreased from 90 to 65%, thus revealing an important activity/selectivity trade-off associated with the reaction temperature. Processing of aqueous ethanol to liquid hydrocarbon product was demonstrated in two sequential catalytic steps: 1) conversion of ethanol to an isobutene/propene-rich gas mixture over Zn1Zr2.5Oz catalyst, followed by 2) oligomerization over solid acid resin (Amberlyst-36). This processing sequence produced a highly branched olefin product primarily in the gasoline range (70% mass yield based on simulated distillation) with a high octane rating (approximate research octane number [RON] of 103). To increase the carbon yield to that of jet-range hydrocarbons, separation of the olefins from the light gases (i.e., H2, CO2, etc.) is required prior to oligomerization. Thus, in a separate set of experiments, an isobutene/propene mixture was converted over either H-beta (200 °C) or Purolite-CT275 (120 °C). This conversion step produced jet-range hydrocarbons with 80–85% mass yield. Upon subsequent distillation and hydrotreatment, both liquid products met select ASTM 7566 Annex A5 specifications for an alcohol-to-jet synthetic paraffinic kerosene (ATJ-SPK) blending component (e.g., specifications for freezing point, flash point, viscosity, and density).

21 August 2021 in ChemSusChem
Verified
Journal Article
Closed access
PDF file
Jotheeswari KothandaramanJotheeswari Kothandaraman
Jotheeswari Kothandaraman
JSJohnny Saavedra
Johnny Saavedra
YJYuan Jiang
Yuan Jiang
EWEric D. Walter
Eric D. Walter
SBSarah D. Burton
Sarah D. Burton
DHDavid J. Heldebrant
David J. Heldebrant

15 December 2015 in ACS Catalysis
Verified
Journal Article
Closed access
DMDonghai Mei
Donghai Mei
VDVanessa Lebarbier Dagle
Vanessa Lebarbier Dagle
RXRong Xing
Rong Xing
KAKarl O. Albrecht
Karl O. Albrecht
RDRobert Dagle
Robert Dagle

19 January 2016 in Green Chemistry
Verified
Journal Article
Closed access
PDF file
VDVanessa Lebarbier Dagle
Vanessa Lebarbier Dagle
CSColin Smith
Colin Smith
MFMatthew Flake
Matthew Flake
KAKarl O. Albrecht
Karl O. Albrecht
MGMichel J. Gray
Michel J. Gray
RDRobert Dagle
Robert Dagle
Efficient synthesis of renewable fuels that will enable cost competitiveness with petroleum-derived fuels remains a grand challenge. In this paper, we report on an integrated catalytic approach for producing transportation fuels from biomass-derived syngas. This novel process represents an alternative to conventional fuel synthesis routes (e.g., Fischer–Tropsch, Methanol-to-Gasoline) that have drawbacks, particularly at the scale of biomass. Composition of the resulting hydrocarbon fuel can be modulated to produce predominantly middle distillates, which is constantly increasing in demand compared to gasoline fraction. In this process biomass-derived syngas is first converted over an Rh-based catalyst into a complex aqueous mixture of condensable C2 + oxygenated compounds (predominantly ethanol, acetic acid, acetaldehyde, ethyl acetate). This multi-component aqueous mixture then is fed to a second reactor loaded with a ZnxZryOz mixed oxide catalyst, which has tailored acid–base sites, to produce an olefin mixture rich in isobutene. The olefins then are oligomerized using a solid acid catalyst (e.g., Amberlyst-36) to form condensable olefins with molecular weights that can be targeted for gasoline, jet, and/or diesel fuel applications. The product rich in long-chain olefins (C7 +) is finally sent to a fourth reactor required for hydrogenation of the olefins into paraffin fuels. Simulated distillation of the hydrotreated oligomerized liquid product indicates that ∼75% of the hydrocarbons (iso-paraffins and cyclic compounds) are in the jet-fuel range. Process optimization for the oligomerization step could further improve yield to the jet-fuel range. All of these catalytic steps have been demonstrated in sequence, thus providing proof-of-concept for a new integrated process for the production of drop-in biofuels. Overall, we demonstrate approximately 41% carbon efficiency for converting syngas into jet-range hydrocarbons. This unique and flexible process does not require external hydrogen and also could be applied to non-syngas derived feedstock, such as fermentation products (e.g., ethanol, acetic acid, etc.), other oxygenates, and mixtures thereof containing alcohols, acids, aldehydes and/or esters.

11 September 2017 in ACS Sustainable Chemistry & Engineering
Verified
Journal Article
Closed access
SDStephen D. Davidson
Stephen D. Davidson
KSKurt A. Spies
Kurt A. Spies
DMDonghai Mei
Donghai Mei
LKLibor Kovarik
Libor Kovarik
IKIgor Kutnyakov
Igor Kutnyakov
RDRobert Dagle
Robert Dagle