Byung Mook Weon

Prof. Byung Mook Weon

Soft Matter Physics Laboratory, School of Advanced Materials Science and Engineering, SKKU Advanced Institute of Nanotechnology (SAINT), Sungkyunkwan University, Suwon 16419, South Korea
orcid

Research Focus & Metrics

Academic Career Length

24Years (2003-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
26 July 2010 in Physical Review E
Verified
Journal Article
Open access
BWByung Mook Weon
Byung Mook Weon
Jung Ho JeJung Ho Je
Jung Ho Je
When a coffee drop dries on a solid surface, it leaves a ringlike deposit along the edge and this is known as the ``coffee-ring effect.'' We find a different motion of particles repelling the coffee-ring effect in drying droplets; the motion of particles that is initially toward the edge by the coffee-ring effect is reversed toward the center by a capillary force. The reversal takes place when the capillary force prevails over the outward coffee-ring flow. We discuss the geometric constraints for the capillary force and the reverse motion. Our findings of reversal phenomena would be important in many scenarios of drying colloidal fluids.

21 June 2011 in Nature Communications
Verified
Journal Article
Open access
JLJi San Lee
Ji San Lee
BWByung Mook Weon
Byung Mook Weon
SPSu Ji Park
Su Ji Park
Jung Ho JeJung Ho Je
Jung Ho Je
KFKamel Fezzaa
Kamel Fezzaa
WLWah-Keat Lee
Wah-Keat Lee
A bubble reaching an air-liquid interface usually bursts and forms a liquid jet. Jetting is relevant to climate and health as it is a source of aerosol droplets from breaking waves. Jetting has been observed for large bubbles with radii of R≫100 μm. However, few studies have been devoted to small bubbles (R<100 μm) despite the entrainment of a large number of such bubbles in sea water. Here we show that jet formation is inhibited by bubble size; a jet is not formed during bursting for bubbles smaller than a critical size. Using ultrafast X-ray and optical imaging methods, we build a phase diagram for jetting and the absence of jetting. Our results demonstrate that jetting in bubble bursting is analogous to pinching-off in liquid coalescence. The coalescence mechanism for bubble bursting may be useful in preventing jet formation in industry and improving climate models concerning aerosol production.

13 November 2012 in Physical Review Letters
Verified
Journal Article
Open access
PDF file
JLJi San Lee
Ji San Lee
BWByung Mook Weon
Byung Mook Weon
Jung Ho JeJung Ho Je
Jung Ho Je
KFKamel Fezzaa
Kamel Fezzaa
When a liquid drop impacts a solid surface, air is generally entrapped underneath. Using ultrafast x-ray phase-contrast imaging, we directly visualized the profile of an entrapped air film and its evolution into a bubble during drop impact. We identified a complicated evolution process that consists of three stages: inertial retraction of the air film, contraction of the top air surface into a bubble, and pinch-off of a daughter droplet inside the bubble. Energy transfer during retraction drives the contraction and pinch-off of a daughter droplet. The wettability of the solid surface affects the detachment of the bubble, suggesting a method for bubble elimination in many drop-impact applications.

11 January 2013 in Physical Review Letters
Verified
Journal Article
Open access
BWByung Mook Weon
Byung Mook Weon
Jung Ho JeJung Ho Je
Jung Ho Je
Colloidal particles suspended in a fluid usually inhibit complete wetting of the fluid on a solid surface and cause pinning of the contact line, known as self-pinning. We show differences in spreading and drying behaviors of pure and colloidal droplets using optical and confocal imaging methods. These differences come from spreading inhibition by colloids confined at a contact line. We propose a self-pinning mechanism based on spreading inhibition by colloids. We find a good agreement between the mechanism and the experimental result taken by directly tracking individual colloids near the contact lines of evaporating colloidal droplets.

17 August 2015 in Scientific Reports
Verified
Journal Article
Open access
PDF file
JKJin Young Kim
Jin Young Kim
KCKun Cho
Kun Cho
SRSeul-A Ryu
Seul-A Ryu
SKSo Youn Kim
So Youn Kim
BWByung Mook Weon
Byung Mook Weon
Crack formation is a frequent result of residual stress release from colloidal films made by the evaporation of colloidal droplets containing nanoparticles. Crack prevention is a significant task in industrial applications such as painting and inkjet printing with colloidal nanoparticles. Here, we illustrate how colloidal drops evaporate and how crack generation is dependent on the particle size and initial volume fraction, through direct visualization of the individual colloids with confocal laser microscopy. To prevent crack formation, we suggest use of a versatile method to control the colloid-polymer interactions by mixing a nonadsorbing polymer with the colloidal suspension, which is known to drive gelation of the particles with short-range attraction. Gelation-driven crack prevention is a feasible and simple method to obtain crack-free, uniform coatings through drying-mediated assembly of colloidal nanoparticles.

3 January 2013 in Physical Review E
Verified
Journal Article
Open access
BWByung Mook Weon
Byung Mook Weon
Jung Ho JeJung Ho Je
Jung Ho Je
Colloidal droplets including micro- and nanoparticles generally leave a ringlike stain, called the ``coffee ring,'' after evaporation. We show that fingering emerges during evaporation inside the coffee ring, resulting from a bidispersed colloidal mixture of micro- and nanoparticles. Microscopic observations suggest that finger formation is driven by competition between the coffee-ring and Marangoni effects, especially when the inward Marangoni flow is overwhelmed by the outward coffee-ring flow. This finding could help to understand the variety of the final deposition patterns of colloidal droplets.