In this paper, vibration control of an unbalanced single-side cantilevered rotor system using a novel integral squeeze film bearing damper in terms of stability, energy distribution, and vibration control is analyzed. A finite element model of such a system with an integral squeeze film bearing damper (ISFBD) is developed. The stability, energy distribution, and vibration control of the unbalanced single-side cantilevered rotor system are calculated and analyzed based on the finite element model. The stiffness of the integral squeeze film bearing damper is designed using theoretical calculation and finite element model (FEM) simulation. The influence of installation position and quantity of integral squeeze film bearing dampers on the vibration control of the unbalanced cantilevered rotor system is discussed. An experimental platform is developed to validate the vibration control effect. The results show that the installation position and quantity of the integral squeeze film bearing dampers have different effects on the stability, energy distribution, and vibration control of the unbalanced cantilevered rotor system. When ISFBDs are installed at both bearing housings, the vibration control is best, and the vibration components of the time and frequency domains have good vibration control effects in four working conditions.
This paper proposes a method for optimizing unbalanced force and unbalanced moment of the multistage disk based on sequence quadratic program algorithm to solve the vibration problem of gas turbine tie rod rotor. This method guides the assembly phase of the multistage disks. The influence of unbalanced force and unbalanced moment on the vibration of the tie rod rotor are analyzed based on the characteristics of rotor structure and assembly process. A dynamic model of the unbalanced force and unbalanced moment of the tie rod rotor is established. The sequence quadratic program algorithm is used to optimize multi-dimension of unbalanced force and moment, so the global optimal solution can be obtained. In order to verify the effectiveness of the optimization method proposed in this paper, vibration control experiments are carried out for traditional tie rod rotor and gas turbine tie rod rotor structure. The results show that both unbalanced force optimization and unbalanced moment optimization can control the tie rod rotor vibration effectively, and unbalanced moment optimization is better. Unbalanced moment optimization is used to perform constant speed and speed-up experiment on the gas turbine tie rod rotor structure. At 1200r/min, the maximum vibration reduction of the system is 76.68%. And the vibration has a decrease of 43.3% at the first-order critical speed. The proposed method in this paper can be used not only for the guidance of tie rod rotor assembly of gas turbine, but also for the vibration control during operation.
A novel type of integral squeeze film damper (ISFD) is proposed to reduce and isolate vibration excitations of the gear system through bearing to the foundation. Four ISFD designs were tested experimentally with an open first-grade spur gear system. Vibration reduction characteristics were experimentally studied at different speeds for cases where ISFD elastic damping supports were simultaneously installed on the driving and driven shafts, installed on the driven shaft, or only installed on the driving shaft. Experimental results show that the ISFD elastic damping support can effectively reduce shock vibration of the gear system. Additionally, resonant modulation in gear shafts caused by meshing impact was significantly reduced. Different vibration amplitudes of gear shafts with ISFD installed only on driven or driving shafts were compared. Results indicated that vibration reduction is better when ISFD is only installed on the driven shaft than on the driving shaft.
12 May 2022 in International Journal of Turbo & Jet-Engines
To solve the poor precision and low efficiency of manual grinding de-weight dynamic balance of turbopump rotor, the laser de-weight dynamic balance technology of rotating machines is adopted. Combined with the advantages of laser de-weight, such as, fast processing speed high machining precision and good machined surface quality, the smooth transition of the machined surface was realized by means of hierarchical machining. According to the characteristics of the turbopump rotor structure, the equivalent transformation model for laser de-weight turbopump rotor was built to convert the unbalance into laser processing parameters, which achieve the rapid and accurate de-weight of turbopump rotor. It focuses on solving the repeatedly loading and low accuracy of manual grinding dynamic balance. To verify the effectiveness of the proposed technique, laser de-weight experiments were carried out on two turbopump rotor test pieces. A dynamic balance test bench was set up to measure the rotor residual unbalance at 1800 r/min test speed, which is low dynamic balance. The results show that the machined surface transition was smooth, the residual unbalance was small and the machining efficiency was high. The effect of laser de-weight dynamic balance reached the expectation. It is an universal technology which is not limited to the dynamic balance of turbopump rotor, but also applicable to other rotating machinery..