Research in nondestructive evaluation is constantly increasing the sensitivity of detection of small cracks embedded deep in layered aircraft structures. Pulsed eddy-current (PEC) techniques using coil probes have shown considerable promise in detection and characterization of buried cracks in multilayered structures. In this paper, we describe the design and development of a nondestructive inspection system that uses pulse excitation of a planar multiline coil to generate a transient field that is detected via a giant magnetoresistive (GMR) field sensor. An analysis algorithm using features in time and frequency domain processes the experimentally measured signals for automatic detection of small cracks under fasteners in multilayered structures at a depth of up to 10 mm.

Eddy current-based techniques have been investigated for the inspection of embedded cracks under fastener heads in riveted structures. However, these techniques are limited in their ability to detect cracks that are not perpendicular to induced current flows. Further, the presence of a steel fastener of high permeability produces a strong signal that masks relatively smaller indication from a crack. In this paper, a rotating electromagnetic field is designed to rotate the applied magnetic fields and related eddy currents electrically so that the sensor shows uniform sensitivity in detecting cracks in all radial directions around fastener sites. Giant magnetoresistive sensors are employed to image the normal component of this rotating field, to detect different crack orientations at aluminum and ferromagnetic fastener sites. Numerical model-based studies and experimental validation are presented.

We evaluated layer-by-layer retinal thickness in spectral-domain optical coherence tomography (SD-OCT), determined by automated segmentation analysis (ASA) software in healthy and early age-related maculopathy (ARM) eyes. There were 57 eyes (specifically, 19 healthy eyes under 60 years old, 19 healthy eyes over 60, and 19 ARM eyes) recruited into this cross-sectional study. The mean ages were 36.78 (SD, ±13.82), 69.89 (SD, ±6.14), and 66.10 (SD, ±8.67) years, respectively, in the three study groups. The SD-OCT scans were transferred into a dedicated software program that performed automated segmentation of different retinal layers. Automated layer segmentation showed clear boundaries between the following layers: retinal nerve fiber layer (RNFL), ganglion cell layer plus inner plexiform layer (GCL+IPL), inner nuclear layer plus outer plexiform layer (INL+OPL), outer nuclear layer (ONL), and RPE complex. The thickness of the RNFL, ONL, and RPE layers did not show a statistically significant change across the three groups by ANOVA (P = 0.10, P = 0.09, P = 0.15, respectively). The thickness of GCL+IPL and INL+OPL was significantly different across the groups (P < 0.01), being reduced in the ARM eyes compared to healthy eyes, under and over 60 years old. The early morphologic involvement of the GCL+IPL and INL+OPL layers in ARM eyes, as revealed by the ASA, could be related to early anatomic changes described in the inner retina of ARM eyes. This finding may represent a morphologic correlation to the deficits in postreceptoral retinal function in ARM eyes.

This paper presents a novel homogenization technique to retrieve the effective permittivity of an interconnect embedded in inhomogeneous dielectrics, with an arbitrary number of conductors. The technique is based on the monotonicity property of suitable matrices associated with the transmission line model. The effective permittivity values are obtained by checking an index related to the eigenvalues of such matrices. The technique requires only the knowledge, at a single frequency point, of any of the terminal matrices describing the original line (e.g., impedance, admittance, or scattering matrices), either obtained by measurements or by simulations. Depending on the applications, the technique can identify one or two values for the effective permittivity. In the first case, the original inhomogeneous line can be replaced by an equivalent line, embedded in a homogeneous dielectric. In the second case, two equivalent homogeneous lines are identified, which cannot replace the inhomogeneous line, but can be used to obtain the lower and upper bounds to its performance (in terms of significant physical signatures, such as stored energy, propagation velocities, delay times, and characteristic impedance). The mathematical theorems supporting the technique are rigorously proven. The technique is shown to be consistent with the existing results in the literature and is experimentally validated. Several case studies are carried out, including cables, microstrips, and multilayered interconnects.