Increased temperature of photovoltaic (PV) module decreases its performance; hence, integration of the cooling system is imperative in minimizing this detrimental effect. In this study, passive cooling of PV module with different heatsinks has been simulated by thermal models using ansys steady-state thermal software. The results were based on the effect of convective heat transfer coefficients from 5 to 1000 W/m2K for the temperature reduction of PV module using 19 different heatsinks. Three configurations: flat plate heat spreader, fin-only heatsinks, and fin-flat base plate combined heatsinks, have been studied at 35 °C ambient temperature and 800 W/m2 solar radiation. The result shows that at convective heat transfer coefficient of 10 W/m2K, the combined type model C7, and the fin-only type model B4 demonstrated around 18.94% and 9.36% lower PV cell temperature, respectively, than the flat plate type model A2. Moreover, C7 and B4 models had about 67.5% and 78.03% less material weight than the A2 model, making the heat spreader type least feasible compared with the other two. The temperature contours of the PV cell layer at a given operating condition showed uniform distribution for both flat plate types and combined types. In contrast, the fin-only heatsink configuration illustrated hotspots within the PV cell layer.
6 April 2022 in Journal of Thermal Science and Engineering Applications
This paper presents performance comparison between different liquid metal based nanofluids termed as nano-liquid-metal-fluids in a microchannel heat sink in order to achieve ultimate cooling solutions without sacrificing the compact structure and heavy computing speed. The hydraulic and thermal performance of nanofluids having five different liquid metals (Ga, GaIn, EGaIn, GaSn, EGaInSn) as base fluid and four different nanoparticles (CNT, Al2O3, Cu, diamond) as solute are evaluated comparing with water based nanofluids. Three-dimensional flow inside miniaturized channels are predicted using single-phase and two-phase numerical simulations. Numerical models are validated against data obtained from experimental studies from literature. Three different grids are developed and several element sizes were compared to obtain the grid independence. Upon evaluation, the study can point out that liquid metal based nanofluids can generate much superior heat transport characteristics with more than 3.41 times higher heat transfer coefficient compared to conventional water based nanofluids. GaIn-CNT combination exhibits the best thermal solution possible with a heat transfer coefficient increment of 2.68%, 17.19%, 22.16%, 2.62% over CNT particle-based EGaIn, EGaInSn, Ga, GaSn liquid metal, respectively for Re = 750. Considering hydraulic performance, PEC (performance evaluation criterion) has been introduced and Ga based nanofluids are found to be most effective in this perspective. The effect on overall cooling effectiveness has also been carried out with a detailed particle concentration study. This study paves the pathway of using these extraordinary coolants in mini/micro channel heat sinks.
1 March 2021 in Transactions of the Canadian Society for Mechanical Engineering
The Hyperloop promises to revolutionize the transport infrastructure of the 21st century by reducing travel time and allowing people to reach transonic speed on land. It carries with it the hope of a sustainable transportation system during an era of global energy crisis. Overall passenger safety in a high-speed pod necessitates a reliable braking system. This paper introduces the possibility of utilizing aerodynamic drag in the Hyperloop, anticipated to operate at high Mach and low Reynolds flow regime, to attenuate the speed of the pod. Numerical analysis was conducted to investigate the effect of incorporating an aerodynamic brake at different pod velocities (100, 135, and 150 m/s) and deployment angles (30°, 45°, 60°, and 90°). A detailed comparison between the proposed aerodynamic braking system (AeBS) and existing braking systems for the Hyperloop has been presented in this paper. The results demonstrate an increase in drag value of the pod by 3.4 times using a single 0.15 m2 brake plate. When the brake plate was fully deployed at a pod velocity in excess of 112 m/s, the aerodynamic drag-based braking systems was shown to be more effective than the contemporary eddy current braking system.
An unsteady numerical investigation was performed to examine time dependent behaviors of the tip leakage flow structures and heat transfer on the rotor blade tip and casing in a single stage gas turbine engine. A transonic, high-pressure turbine stage was modeled and simulated using a stage pressure ratio of 3.2. The rotor’s tip clearance was 1.2 mm in height (3% of the rotor span) and its speed was set at 9500 rpm. Periodic flow is observed for each vane passing period. Tip leakage flow as well as heat transfer data showed highly time dependent behaviors. A stator trailing edge shock appears as the turbine stage is operating at transonic conditions. The shock alters the flow condition in the rotor section, namely, the tip leakage flow structures and heat transfer rate distributions. The instantaneous Nusselt number distributions are compared to the time averaged and steady-state results. The same patterns in tip leakage flow structures and heat transfer rate distributions were observed in both unsteady and steady simulations. However, the unsteady simulation captured the locally time-dependent high heat transfer phenomena caused by the unsteady interaction with the upstream vane trailing-edge shock and the passing wake.
17 February 2025 in Journal of Solar Energy Engineering
The reduction in efficiency of photovoltaic (PV) modules when operating at high temperatures is a challenge that demands effective and economical cooling solutions. As such, aluminum heat sinks provide a passive and carbon-neutral cooling method. This study aims to find the performances of five different geometries of aluminum heat sinks to be used for cooling PV modules, where a comparative analysis of their relative performances under controlled environmental variables is performed under steady-state condition. The results show that an arrangement of solid T-shaped aluminum fins as heat sinks provides a 3.14% further reduction in PV module temperature compared to its perforated counterpart. The variation of the average PV module temperature has been compared in terms of solar radiation, ambient temperature, as well as the convection heat transfer coefficients for each heat sink geometry, where the relationship between each pair of data has been identified. The analysis reveals that performance differences may be better observed at lower values for the convection coefficient and higher values for the ambient temperatures. The methodology followed in this study provides a base model for comparing the relative performances of the chosen heat sink geometries, thus providing scopes of continuation of this work.
The world’s reliance on non-renewable energy sources is unsustainable, and biogas production from organic waste materials is a promising renewable energy source. However, there is a lack of technology and understanding surrounding biogas production and utilization. This study aimed to produce biogas at laboratory scale using cafeteria waste and to examine the processes of biogas production for variable factors such as retention time, pH level, and addition of bases. The findings showed that a mixture of papaya peels, water, cow manure, and a base produced an impressive 80.75% methane yield within 75 days under mesophilic conditions with a specific pH and temperature range. However, maintaining optimal pH and vacuum in a biogas chamber presents challenges, such as leakages and pH fluctuations. The optimal ratio for biogas production is a mixture of 45-50% organic matter and 55-60% water, with careful regulation of base addition to ensure maximum biogas production and optimal biogas quality. This study provides insights into biogas production and its potential as a viable biofuel alternative.