Anhydrobiosis is a unique state of live organisms in which their metabolism is temporary reversibly suspended as the result of strong dehydration of their cells. This state is widely used currently during large-capacity production of active dry baker’s yeast. Other strains of the yeast Saccharomyces cerevisiae, as well as other yeast species that could potentially find use in modern biotechnology, are not resistant to dehydration–rehydration treatments. To improve their resistance, the main factors that influence cell survival during such treatment need to be revealed. This study showed the importance of mitochondria for yeast cell survival during transfer into anhydrobiosis, a factor that was strongly underestimated until this study. It was revealed that the external introduction inside yeast cells of 50 μM of lithocholic acid (LCA), an agent that induces changes in glycerophospholipids in mitochondrial membranes, in combination with 1% DMSO, may improve the survival rate of dehydrated cells. The influence of LCA upon yeast cell resistance to dehydration–rehydration was not linked with changes in the state of the cells’ plasma membrane.
Anhydrobiosis is the state of life when cells are exposed to waterless conditions and gradually cease their metabolism. In this study, we determined the sequence of events in Saccharomyces cerevisiae energy metabolism during processes of dehydration and rehydration. The intensities of respiration and acidification of the medium, the amounts of phenyldicarbaundecaborane (PCB−) bound to yeast membranes, and the capabilities of cells to accumulate K+ were assayed using an electrochemical monitoring system, and the intracellular content of ATP was measured using a bioluminescence assay. Mesophilic, semi-resistant to desiccation S. cerevisiae strain 14 and thermotolerant, very resistant to desiccation S. cerevisiae strain 77 cells were compared. After 22 h of drying, it was possible to restore the respiration activity of very resistant to desiccation strain 77 cells, especially when glucose was available. PCB− binding also indicated considerably higher metabolic activity of dehydrated S. cerevisiae strain 77 cells. Electrochemical K+ content and medium acidification assays indicated that permeabilization of the plasma membrane in cells of both strains started almost simultaneously, after 8–10 h of desiccation, but semi-resistant strain 14 cells maintained the K+ gradient for longer and more strongly acidified the medium. For both cells, the fast rehydration in water was less efficient compared to reactivation in the growth medium, indicating the need for nutrients for the recovery. Higher viability of strain 77 cells after rehydration could be due to the higher stability of their mitochondria.
An interesting development of biotechnology has linked microbial cell immobilisation with nanoparticles. The main task of our research was to reveal the possible influences of differently electrically charged diamond nanoparticles upon physiological characteristics of the yeast Saccharomyces cerevisiae. It was revealed that the adverse impact of these nanoparticles can manifest not only against prokaryotes, but also against eukaryotic yeast cells. However, the obtained results also indicate that it is possible to reduce and, most likely, completely eliminate the dangerous effects of nanoparticles to cells by using special physical approaches. Comparison of non-arylated and arylated nanoparticles showed that in terms of changes in the physiological activity of cells, which are important to biotechnology and biomedicine, the selection of certain nanoparticles (non-arylated or arylated) may be necessary in each specific case, depending on the purpose of their use.
Titanium and its alloys are widely used in endoprostheses. The naturally formed titanium dioxide film on titanium surfaces improves chemical stability and enhances implant biocompatibility. However, oxidised titanium surfaces may also promote bacterial adhesion and biofilm formation, contributing to implant-associated infections. Therefore, surface modification represents a key strategy for controlling microbial–implant interactions. This article focuses widely used titanium alloy Ti-6Al-4V treated with a laser beam, which induces surface colour changes as a result of oxide formation. Laser processing enables controlled formation of micro- and nanoscale features, structural reconstructions, and defects that may influence the surface electrical charge and, consequently, cell immobilisation. Thus, the surface colour, electrical potential, and cell immobilisation capacity are likely interrelated. From a manufacturing perspective, titanium oxide colouring facilitates quality control and process reproducibility, as surface colour provides a rapid, non-destructive visual indicator of oxide thickness and treatment consistency. This study aims to identify correlations among surface colour, electrical potential, and cell immobilisation capacity on laser-treated titanium alloys. A relationship between the optical properties, electronic structure, and biological response of laser-processed titanium oxide films is established. Specifically, the blue colour saturation of the oxide film is inversely correlated with the electron work function. A more saturated blue corresponds to a lower work function, indicating a higher positive surface charge density. This shift is attributed to changes in electron affinity, likely resulting from laser-induced structural reconstruction and defect formation within the oxide layer. The proposed changes in electronic structure are supported by modifications in the electronic density of states, analysed using near-threshold photoelectron spectroscopy. The biological response is directly linked to these physical changes: enhanced immobilisation of yeast (Saccharomyces cerevisiae) cells on the treated alloy surface correlates with the electron work function. These results may assist in the development of controlled titanium oxide surfaces with enhanced biocompatibility.