Nanostructured bainite (NB) bearing steel has excellent strength and ductility combinations, which can improve the fatigue life and wear resistance of bearing steel in harsh conditions. However, the phase transformations and the correlation between the microstructure and wear properties of NB bearing steel are still unclear. In this study, bearing steels with different Si contents (GCr15SiMo and GCr15Si1Mo) were prepared to have nano-bainitic structures, and their microstructure transformations and wear mechanisms were investigated. The results show that the Si element can inhibit the precipitation of carbides and can then promote the block-like retained austenite formation and refine the bainitic ferrite lamellar structure. The impact energy of GCr15Si1Mo is larger than that of GCr15SiMo because the nanostructured bainite and retained austenite are the main toughness phase in these steels. The wear results indicate that the steels which possess appropriate strength and toughness are helpful for improving wear resistance properties. Finally, the wear resistance performance of the GCr15Si1Mo austempered at 210 °C and GCr15SiMo austempered at 230 °C was good in this work.

Using Cr₇C₃/Ni₃Al alloyed powder and Cr₃C₂/Ni₃Al mixed powder, laser cladding was carried out to prepare a Cr₇C₃ reinforced Ni₃Al composite cladding layer. The microstructure and tribological properties of the cladding materials were investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), transmission electron microscopy (TEM), and wear tests. The results indicate that the microstructure of the Cr₇C₃/Ni₃Al alloyed powder cladding layer contains mainly Ni₃Al, NiAl, and in situ-formed Cr₇C₃, whereas Cr₃C₂ occurs in the Cr₃C₂/Ni₃Al mixed powder cladding layer. The friction coefficient and wear loss of the alloyed powder cladding layer are about 0.1 and 0.75 mg, respectively, which are less than those of the mixed powder cladding layer (0.12 and 0.8 mg). Moreover, the alloyed powder cladding layer is much friendlier to its counterpart. The counterpart’s loss weight of the alloyed powder cladding layer decreases 42.2% than the mixed powder cladding layer. The reason can be attributed to the homogeneous distribution of fine in situ-formed Cr₇C₃ in the alloyed powder cladding materials, which can effectively separate the friction pair, improving the wear resistance of the cladding materials.

Solid solution and coupling precipitation behavior of multiple microelements in 50CrVA spring steel under different temperatures were analyzed based on thermodynamics. Quantitative relationships between the multiple microelements’ contents and secondary phases, and their effects on fatigue life, were systematically studied in conjunction with the secondary phase microstructure characterization using scanning and transmission electron microscopy, etc. The solid solution contents of different microelements decreased as the temperature decreased, especially N and Ti, but the number of compounds gradually increased when the temperature decreased. Carbonitride constitutional liquation occurred in 50CrVA-S1# spring steel-containing microparticles, and without carbonitrides, constitutional liquation occurred in 50CrVA-S2# spring steel-containing nanoparticles. The experimental results indicate that the fatigue life reduces by about an order of magnitude when the secondary phase size changes from nanometers to microns, and the corresponding relationship among multiple microelements, microstructure of secondary phases, and fatigue life, was established in this spring steel.

Copper alloys with a combination of good electrical conductivity and mechanical properties are widely used in automotive electronics, large-scale integrated circuits, and other fields. In this study, a new type of Cu–Ni–Si alloy with added trace elements of Co and Cr was fabricated. Hot compression tests of this alloy at different temperatures and strain rates were conducted using a Gleeble-1500D simulator. Then, the microstructure transformation and precipitation behaviors of the Cu-1.1–Ni-0.7–Co-0.45–Si-0.3Cr alloy were studied during a hot deformation process. The results show that the hot deformation behavior of the Cu-1.1–Ni-0.7–Co-0.45–Si-0.3Cr alloy includes continuous dynamic recrystallization (CDRX) and discontinuous dynamic recrystallization (DDRX). The intensity of the texture in the microstructure is decreased, and the randomness of the texture in the microstructure is increased together with the recrystallization progress. The degree of recrystallization of the new Cu-1.1–Ni-0.7–Co-0.45–Si-0.3Cr alloy is increased when the hot deformation temperature rises. Additionally, the results indicate that there are two types of precipitates which are formed in the alloy during the hot deformation process. These two precipitates can pin dislocations and grain boundaries, and therefore, they significantly improve the hot compression resistance of the Cu-1.1–Ni-0.7–Co-0.45–Si-0.3Cr alloy.