Magnesium (Mg) and Mg alloys are considered as potential candidates for biomedical applications because of their high specific strength, low density, and elastic modulus, degradability, good biocompatibility and biomechanical compatibility. However, the rapid corrosion rate of Mg alloys results in premature loss of mechanical integrity, limiting their clinical application in load-bearing parts. Besides, the low strength of Mg alloys restricts their further application. Thus, it is essential to understand the characteristics and influencing factors of mechanical and corrosion behavior, as well as the methods to improve the mechanical performances and corrosion resistance of Mg alloys. This paper reviews the recent progress in elucidating the corrosion mechanism, optimizing the composition, and microstructure, enhancing the mechanical performances, and controlling the degradation rate of Mg alloys. In particular, the research progress of surface modification technology of Mg alloys is emphasized. Finally, the development direction of biomedical Mg alloys in the future is prospected.

Magnetic nanomaterials are widely used in biosynthesis, catalysis, as electronic and microwave-absorbing materials, and in environmental treatment because of their high specific surface area, strong magnetism, chemical stability, and good biocompatibility. The chemical coprecipitation method is widely used for the preparation of magnetic nanomaterials due to its simplicity, low cost, and easily-controlled operating conditions. The magnetic nanomaterials prepared by the chemical coprecipitation method are summarized according to the different compositions, including the basic preparation principles, and the factors affecting their morphology, size, and microstructure. The mechanisms of preparing magnetic nanomaterials by chemical precipitation and the process control factors are emphasized. Finally, the preparation of magnetic nanomaterials by chemical coprecipitation is summarized and prospected.

Two‐dimensional transition metal dichalcogenides (2D TMDs) present promising applications in various fields such as electronics, optoelectronics, memory devices, batteries, superconductors, and hydrogen evolution reactions due to their regulable energy band structures and unique properties. For emerging spintronics applications, materials with excellent room‐temperature ferromagnetism are required. Although most transition metal compounds do not possess room‐temperature ferromagnetism on their own, they are widely modified by researchers using the emerging strategies to engineer or modulate their intrinsic properties. This paper reviews recent enhancement approaches to induce magnetism in 2D TMDs, mainly using doping, vacancy defects, composite of heterostructures, phase modulation, and adsorption, and also by electron irradiation induction, O plasma treatment, etc. On this basis, the produced effects of these methods for the introduction of magnetism into 2D TMDs are compressively summarized and constructively discussed. For perspective, research on magnetic doping techniques for 2D TMDs materials should be directed toward more reliable and efficient directions, such as exploring advanced design strategies to combine dilute magnetic semiconductors, antiferromagnetic semiconductors, and superconductors to develop new types of heterojunctions; and advancing experimentation strategies to fabricate the designed materials and enable their functionalities with simultaneously pursuing the upscalable growth methods for high‐quality monolayers to multilayers.

Many urgently needed inconel superalloy parts with complex internal cavity geometry and high surface precision are difficult to prepare by traditional subtractive manufacturing methods because of its poor machinability. The additive manufacturing technology that has emerged in recent years became a research hotspot in the manufacture of refractory and difficult-to-process metals. In the present study, selective laser melting (SLM), a typical additive manufacture technology, was used to prepare Inconel 718 samples. The influences of input laser energy density ((E, J/mm³) on densification behavior, phases composition, microstructures, microhardness, and wear performance of the SLM as-built Inconel 718 samples were explored in detail. X-ray diffraction (XRD), optical microscopy (OM), scanning electron microscopy (SEM), and transmission electron microscopy (TEM) were used to examine the phase composition and microstructure evolutions. The results show that the formablity, microstructures and mechanical properties of the printed samples were all improved with the increase of E within the parameter setting range of this study. At a lower E, the poor surface morphology and balling effect occurred, the density, hardness, and wear resistance were all at a relatively lower level. When an E value of 190 J/mm was properly set, the surface open-pores and balling effect disappeared, the laser scanning tracks became smooth and continuous, the near-full dense (99.15%) and specimens with good metallurgical bonding and no critical defect were obtained, in which the average microhardness value reached 348 HV_0.2 and wear rate was 5.67 × 10⁻⁴ mm³/N·m. The homogeneity of the superalloy Inconel 718 was also explored.