Arnab Roy

Dr. Arnab Roy


Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications

18 October 2019 in Journal of Engineering for Gas Turbines and Power
Verified
Journal Article
Closed access
PDF file
ARArnab Roy
Arnab Roy
CBClinton R. Bedick
Clinton R. Bedick
DFDonald H. Ferguson
Donald H. Ferguson
TSTodd Sidwell
Todd Sidwell
PSPeter A. Strakey
Peter A. Strakey
Propagation characteristics of a detonation wave in an air-breathing rotating detonation combustor (RDC) using natural gas (NG)–hydrogen fuel blends is presented in this paper. Short-duration (∼up to 6 s) experiments were performed on a 152.4 mm OD uncooled RDC with two different annulus gap widths (5.08 mm and 7.62 mm) over a range of equivalence ratios (0.6–1.0) at varying inlet air temperatures (∼65–204 °C) and NG content (up to 15%) with precombustion operating pressure slightly above ambient. It was observed that the RDC, with an annulus gap width of 5.08 mm, was inherently unstable when NG was added to the hydrogen fuel while operating at precombustion pressures near ambient and at an inlet air temperature of 65 °C. Increasing the annulus gap width to 7.62 mm improved the stability of the detonation wave at similar temperatures and pressure permitting operation with as much as 5% NG by volume. While observed speeds of the detonation waves were still below theoretical values, an increase in inlet air temperature reduced the variability in wave speed. The frequency analysis thus explored in this study is an effort to quantify detonation instability in an RDC under varying operational envelope. The data presented are relevant toward developing strategies to sustain a stable detonation wave in an RDC using NG for land-based power generation.

20 September 2016 in Journal of Turbomachinery
Verified
Journal Article
Closed access
PDF file
KPKapil V. Panchal
Kapil V. Panchal
SASantosh Abraham
Santosh Abraham
ARArnab Roy
Arnab Roy
SESrinath V. Ekkad
Srinath V. Ekkad
WNWing Ng
Wing Ng
MCMichael E. Crawford
Michael E. Crawford

8 April 2020 in Journal of Energy Resources Technology
Verified
Journal Article
Closed access
PDF file
JBJim Black
Jim Black
DSDoug Straub
Doug Straub
EREd Robey
Ed Robey
JYJoe Yip
Joe Yip
SRSridharan Ramesh
Sridharan Ramesh
MSMatthew Searle
Matthew Searle

7 September 2021 in Journal of Turbomachinery
Verified
Journal Article
Closed access
PDF file
MSMatthew Searle
Matthew Searle
ARArnab Roy
Arnab Roy
JBJames Black
James Black
DSDouglas Straub
Douglas Straub
SRSridharan Ramesh
Sridharan Ramesh

23 September 2022 in Journal of Engineering for Gas Turbines and Power
Verified
Journal Article
Closed access
PDF file
ARArnab Roy
Arnab Roy
MSMatthew Searle
Matthew Searle
SRSridharan Ramesh
Sridharan Ramesh
DSDouglas Straub
Douglas Straub
Experimental and numerical investigation of internal cooling channels with rib turbulators is presented with sCO2 flow at pressure-20.7MPa and temperature up to 150°C. The effect of channel aspect ratio up to 2:1 on thermal-hydraulic performance is explored in additively manufactured rectangular and square channels, both with and without 60° ribs on the top and bottom sides. The Wilson-plot method is employed to measure channel averaged Nusselt number over a Reynolds number range up to 370,000. The friction factor and the overall thermal performance factor (TPF) are also reported. The computational fluid dynamics (CFD) simulation is performed for the rib-turbulated configurations reported in the experiments. The objective of the numerical study is to gain insight into the local heat transfer augmentation in the ribbed channels varying the aspect ratio, channel configuration, operating conditions and surface roughness. Surface roughness is simulated using sand grain roughness height (Ks) calculated from the experimental data, and a comparison is presented with varying surface roughness heights ranging between Ks = 0 - 40µm. Experimental results indicate that the heat transfer augmentation is negligible in the rectangular channels with ribs on the long side compared to the square channel. However, it is enhanced by 60% in comparison to placing ribs on the shorter side. The TPF remains constant at around 1 for the entire range of Reynolds numbers. The simulation results highlight that increased surface roughness can have a considerable influence on Nusselt number and overall TPF.