Tong Zhang

Dr. Tong Zhang


Research Focus & Metrics

Academic Career Length

15Years (2012-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
17 April 2019 in Rock Mechanics and Rock Engineering
Verified
Journal Article
Closed access
PDF file
TZTong Zhang
Tong Zhang
QGQuan Gan
Quan Gan
YZYixin Zhao
Yixin Zhao
GZGuangpei Zhu
Guangpei Zhu
XNXiaodong Nie
Xiaodong Nie
JLJiazhuo Li
Jiazhuo Li

30 July 2020 in Natural Resources Research
Verified
Journal Article
Closed access
PDF file
TZTong Zhang
Tong Zhang
LYLiang Yuan
Liang Yuan
KYKe Yang
Ke Yang
YLYang Liu
Yang Liu
FWFei Wei
Fei Wei
XYXiang Yu
Xiang Yu


1 January 2012 in Journal of Enhanced Heat Transfer
Verified
Journal Article
Closed access
HTHou Kuan Tam
Hou Kuan Tam
LTLap Mou Tam
Lap Mou Tam
AGAfshin J. Ghajar
Afshin J. Ghajar
STSik Chung Tam
Sik Chung Tam
TZTong Zhang
Tong Zhang
For internally microfin tubes, most of the heat transfer and friction factor studies were focused on the turbulent region. However, there is a lack of information about the heat transfer and friction factor behavior of microfin tubes in the entire flow regime that covers laminar, transition, and turbulent regions. Furthermore, the effects of fin geometries and inlet configurations on microfin tube heat transfer and friction factor were seldom discussed. Therefore, an experimental study for friction factor and heat transfer on three microfin tubes with different inlet configurations (squared-edge and re-entrant) was conducted and the measured data were compared with the data of a plain tube. From the friction factor and heat transfer results, the transition from laminar to turbulent was clearly established and shown to be inlet- and spiral-angle dependent. For all the microfin tubes with two inlet types, it was observed that the efficiency index was larger than 1 when the Reynolds number was larger than 5000. The current microfin tubes data were also compared with the existing heat transfer and friction factor correlations in the turbulent region. Finally, the genetic algorithms and the algorithms of changes were applied to the existing turbulent correlations to find the optimal fin geometry. The efficiency index computed by both numerical methods outperformed the index computed by the fin geometries used in the past studies. This proved that both algorithms were capable of finding the optimal fin geometry of the microfin tubes

24 September 2020 in Geofluids
Verified
Journal Article
Open access
PDF file
SLShuai Liu
Shuai Liu
KYKe Yang
Ke Yang
TZTong Zhang
Tong Zhang
CTChunan Tang
Chunan Tang
Fully-mechanized mining of coal face with a large cutting height is generally jeopardized by rib spalling disaster in the working face. Preventive measures based on undisturbed coal seam conditions fail to provide safe predictions, as large-scale fractures in soft coal face frequently appear before excavation due to mining-induced stresses. This paper investigates a case study of the Paner Mine 11224 working face in the Huainan mine area, China, which features an overlying protected layer in the protective seam mining. To simulate the failure process in such a mine, we elaborated a simplified physical-mechanical model of a coal wall that underwent shear failure and sliding instability, in compliance with the triangular prism unit criterion. Similar simulation experiments, theoretical calculations, and borehole monitoring were used to comprehensively analyze the overburden fracture and movement after mining the lower protective seam. The development height of three overburden zones was determined, and the characteristics of the protected layer affected by mining were obtained. The results show that the failure is mainly related to the roof load, coal cohesion, internal friction angle, coal seam inclination, and sidewall protecting force. The key to limiting the frictional sliding of a slip body is to reduce the roof load and increase the sliding coefficient and cohesion of the main control weak surface (MCWS). Besides, a self-developed three-dimensional numerical calculation software RFPA3D (Realistic Fracture Process 3D Analysis), which considered the rock heterogeneity, was used to reproduce a weak triangular prism’s progressive failure process. The numerical simulation results agreed with the fracture pattern predicted by the theoretical model, which accurately described the rib spalling mechanisms in a soft coal face with a large cutting height and a protective layer.

3 May 2022 in Natural Hazards
Verified
Journal Article
Closed access
PDF file
YLYang Liu
Yang Liu
TZTong Zhang
Tong Zhang
YMYankun Ma
Yankun Ma
SSShuaibing Song
Shuaibing Song
MTMing Tang
Ming Tang
YLYanfang Li
Yanfang Li