The review presents data on the synthesis, properties of carbon-containing compounds, and their application in the technology of obtaining functional and structural composites. Such materials are widely used in recent years due to their good physical and mechanical properties. The review discusses in detail the influence of the chemical composition of various carbon-containing substances and the size of the dispersed phase on the mechanical and physical properties of produced metal matrix composite. The review also concerns methods for the modern synthesis of graphene, carbon nanotubes, and metallic functional and structural composites with reinforcing carbon-containing compounds. Additionally, the results of metal matrix composite modeling are presented. They show that the improved mechanical properties of CNT–Al composites can be attributed to three factors: CNT hardening, matrix grain refinement, and layered architecture.

When creating titanium-containing bone implants, the bioactive coatings that promote their rapid engraftment are important. The engraftment rate of titanium implants with bone tissue depends significantly on the modification of the implant surface. It is achieved by changing either the relief or the chemical composition of the surface layer, as well as a combination of these two factors. In this work, we studied the creation of composite coatings with a two-level (the micro- and nanolevel) hierarchy of the surface relief, which have bioactive and bactericidal properties, which are promising for bone implantation. Using the developed non-lithographic template electrochemical synthesis, a composite coating on titanium with a controlled surface structure was created based on an island-type TiO₂ film, silver and hydroxyapatite (HAp). This TiO₂/Ag/HAp composite coating has a developed surface relief at the micro- and nanolevels and has a significant cytological response and the ability to accelerate osteosynthesis, and also has an antibacterial effect. Thus, the developed biomaterial is suitable for production of dental and orthopedic implants with improved biomedical properties.

Joint replacement is being actively developed within modern orthopedics. One novel material providing fast implantation is bioactive coatings. The synthesis of targeted nanocoatings on metallic nanotitanium surface is reported in this paper. TiO₂-based micro- and nanocoatings were produced by sol-gel synthesis using dip-coating technology with subsequent fast (shock) drying in hot plate mode at 400 °C. As a result of shock drying, the two-level hierarchical TiO₂ nanolayer on the nanotitanium was obtained. This two-level hierarchy includes nanorelief of porous xerogel and microrelief of the micron-sized “defect” network (a crack network). The thickness of TiO₂ nanolayers was controlled by repeating dip-coating process the necessary number of times after the first layer deposition. The state of the MS3T3-E1 osteoblast cell line (young cells that form bone tissue) on the two-level hierarchical surface has been studied. Particularly, adhesion character, adhesion time and morphology have been studied. The reported results may serve the starting point for the development of novel bioactive coatings for bone and teeth implants.

In the present work the possibility is considered of a chemical sensor synthesis for quantitative glutathione (GSH) determination. Sensor is based on a composite working electrode containing an array of micron-sized Ag particles immobilized on a conductive substrate (Ti) coated by dielectric TiO₂ film. To determine GSH in biological fluids, particularly, in saliva, electrochemical silver-based sensors can be used, since such sensors contain –SH group. With the use of cyclic voltammetry (CV) with a composite working electrode containing an Ag microparticles array, the threshold of quantitative GSH determination is reduced to nM level. Since other modern analogues are inferior at least one order of magnitude in the limit of quantitative GSH detection, we assume that the proposed sensor may be of great interest for clinical diagnosis.

Modern materials science, both in terms of functional and structural materials, is actively developing towards the creation of structures with a given ordering. A wide range of methods involves ordering the structure according to a template shape. Template synthesis is one of the mots wide-spread approaches. Most often, the template synthesis method is implemented under conditions of limiting the growth of the phase due to the geometry of the template. In the present work, a template electrochemical method is considered for calcium hydroxyapatite (HAp) coating synthesis, based on the replication of the planar template texture during deposition. In this case, the template is an array of silver microparticles immobilized on an electrically conductive substrate, separated by an insulator layer. The developed approach is similar to the mask metallization widely used in planar technology. In this work, the possibility of the template pulsed electrodeposition of ceramics rather than metal is shown using HAp as an example. This approach is interesting for materials science, in particular, for obtaining micro-ordered hydroxyapatite structures—a crystallochemical analogue of the inorganic bone tissue component—on the surface of bone implants, which can be implemented to improve their biomedical characteristics. As a result of our study, we experimentally determined the conditions for obtaining the composite coating TiO₂/Ag/Ca₁₀(PO₄)₆(OH)₂ with controlled phase structure, topology and localization of components on the surface, which was confirmed by Scanning Electron Microscopy, Energy Dispersive Spectroscopy, and X-ray Diffraction (SEM, EDS and XRD). The absence of cytotoxicity for the osteoblast-like cells of the developed coating was revealed by cytological tests.

This work is devoted to the development of non-lithographic template methods of synthesis. These methods have a significant advantage in terms of structure formation: there is no need to design and produce masks, which greatly simplifies the process, and more of them can work with nonplanar substrates. The purpose of this study was to reveal the conditions for the synthesis of titanium dioxide xerogel films of different topologies as well as to develop a technique for non-lithographic template electrochemical synthesis of micron metal particles arrays and to study the structure of the resulting coatings. The films were deposited on the surface of substrates via dip coating. Specific topology of the films was achieved by template sol-gel synthesis. Their structures were analyzed by SEM and XRD. Template synthesis of metal micro particles were realized by pulsed electrochemical deposition of metals into the perforations of xerogel films. Obtained materials were analyzed by SEM and XRD; the element distribution on the surface was determined by the EDS detector of SEM. Based on the analysis results, we suggest the mechanisms of formation of the xerogel topology and proved the efficiency of pulsed electrodeposition for template synthesis of micron particles arrays.