The fire-tolerant eucalypt forests of south eastern Australia are assumed to fully recover from even the most intense fires; however, surprisingly, very few studies have quantitatively assessed that recovery. The accurate assessment of horizontal and vertical attributes of tree crowns after fire is essential to understand the fire’s legacy effects on tree growth and on forest structure. In this study, we quantitatively assessed individual tree crowns 8.5 years after a 2009 wildfire that burnt extensive areas of eucalypt forest in temperate Australia. We used airborne LiDAR data validated with field measurements to estimate multiple metrics that quantified the cover, density, and vertical distribution of individual-tree crowns in 51 plots of 0.05 ha in fire-tolerant eucalypt forest across four wildfire severity types (unburnt, low, moderate, high). Significant differences in the field-assessed mean height of fire scarring as a proportion of tree height and in the proportions of trees with epicormic (stem) resprouts were consistent with the gradation in fire severity. Linear mixed-effects models indicated persistent effects of both moderate and high-severity wildfire on tree crown architecture. Trees at high-severity sites had significantly less crown projection area and live crown width as a proportion of total crown width than those at unburnt and low-severity sites. Significant differences in LiDAR -based metrics (crown cover, evenness, leaf area density profiles) indicated that tree crowns at moderate and high-severity sites were comparatively narrow and more evenly distributed down the tree stem. These conical-shaped crowns contrasted sharply with the rounded crowns of trees at unburnt and low-severity sites and likely influenced both tree productivity and the accuracy of biomass allometric equations for nearly a decade after the fire. Our data provide a clear example of the utility of airborne LiDAR data for quantifying the impacts of disturbances at the scale of individual trees. Quantified effects of contrasting fire severities on the structure of resprouter tree crowns provide a strong basis for interpreting post-fire patterns in forest canopies and vegetation profiles in Light Detection and Ranging (LiDAR) and other remotely-sensed data at larger scales.
2 December 2020 in International Journal of Remote Sensing
Forest inventory parameters, in particular DBH (diameter at breast height) and tree height, can be used to accurately estimate above-ground carbon, which is an important indicator of forest productivity and sequestration of carbon. This study demonstrates and tests a method to automatically and manually derive forest inventory parameters for estimating above-ground carbon (AGC) using a Terrestrial Laser Scanner (TLS). The study was conducted in the Royal Belum State Park of Peninsular Malaysia by establishing 24 circular inventory sample plots of 0.05 ha. A RIEGL VZ-400 TLS system was used to acquire point cloud data of the sample plots through multiple scanning, and these data were further pre-processed and co-registered using the RiSCAN PRO software. The DBH and tree height for each tree within the plots were manually measured using a distance measurement tool in RiSCAN PRO and automatically derived from Computree software using a tree segmentation approach. The inventory parameters derived from TLS were compared with the field measurements for calculating the AGC using an allometric equation. On average, 89% and 90% of the sampled trees were detected from the point cloud data of the plots using the manual and automatic detection methods, respectively. The mean values of R2 (coefficient of determination) and RMSE (Root Mean Square Error) for manually measured DBH and tree height across the plots were 0.95 and 2.70 cm, and 0.77 and 2.96 m, respectively. We also obtained an average value of 0.86 and 2.47 cm, and 0.51 and 3.15 m for R2 and RMSE, respectively between field-measured and automatically derived DBH and tree height from TLS data across all the sample plots of the study area. Our method provides clear evidence that TLS has the potential to derive forest inventory parameters, which can be used to estimate above-ground carbon in the tropical rainforest accurately.
23 June 2016 in The International Archives of the Photogrammetry, Remote Sensing and Spatial Information Sciences
This research was conducted to derive forest sample plot inventory parameters from terrestrial LiDAR (T-LiDAR) for estimating above ground biomass (AGB)/carbon stocks in primary tropical rain forest. Inventory parameters of all sampled trees within circular plots of 500 m2 were collected from field observations while T-LiDAR data were acquired through multiple scanning using Reigl VZ-400 scanner. Pre-processing and registration of multiple scans were done in RSCAN PRO software. Point cloud constructing individual sampled tree was extracted and tree inventory parameters (diameter at breast height-DBH and tree height) were measured manually. AGB/carbon stocks were estimated using Chave et al., (2005) allometric equation. An average 80 % of sampled trees were detected from point cloud of the plots. The average of plots values of R2 and RMSE for manually measured DBHs were 0.95, 2.7 cm respectively. Similarly, the average of plots values of R2 and RMSE for manually measured trees heights were 0.77, 2.96 m respectively. The average value of AGB/carbon stocks estimated from field measurements and T-LiDAR manually derived DBHs and trees heights were 286 Mg ha-1 and 134 Mg ha−1; and 278 M ha-1 and 130 Mg ha−1 respectively. The R2 values for the estimated AGB and AGC were both 0.93 and corresponding RMSE values were 42.4 Mg ha−1 and 19.9 Mg ha−1 respectively. AGB and AGC were estimated with 14.8 % accuracy.
30 April 2019 in International Journal of Remote Sensing
Aboveground forest biomass and carbon estimation at landscape scale is crucial for implementation of REDD+ programmes. This study aims to upscale the forest carbon estimates using GeoEye-1 image and small footprint lidar data from small areas to a landscape level using RapidEye image. Species stratification was carried out based on the spectral separability curve of GeoEye-1 image, and comparison of mean intensity and mean plot height of the trees from lidar data. GeoEye-1 image and lidar data were segmented using region growing approach to delineate individual tree crowns; and the segmented crowns (CPA) of tree were further used to establish a relationship with field measured carbon and total trees’ height. Carbon stock measured from field, individual tree crown (ITC) segmentation approach and area-based approach (ABA) was compared at plot level using one-way ANOVA and post hoc Tukey comparison test. ITC-based carbon estimates was used to establish a relationship with spectral reflectance of RapidEye image variables (NDVI, RedEdge NDVI, PC1, single band of RedEdge, and NIR) to upscale the carbon at landscape level. One-way ANOVA resulted in a highly significant difference (p-value < 0.005) between the mean plot height and lidar intensity to stratify Shorea robusta and Other species successfully. ITC carbon stock estimation models of two major tree species explained about 88% and 79% of the variances, respectively, at 95% confidence level. The ABA estimated carbon was highly correlated (R2 = 0.83, RMSE = 20.04) to field measured carbon with higher accuracy than the ITC estimated carbon. A weak relationship was observed between the carbon stock and the RapidEye image variables. However, upscaling of carbon estimates from ABA is likely to improve the relationship of the RapidEye variables rather than upscaling the carbon estimates from ITC approach.