The objective of this study is to evaluate the approaches to improve the durability and strength of the porous asphalt through laboratory testing. Porous asphalt specimens were prepared using three types of binders: high-viscosity binder (HVB), PG76-22 and PG70-22. Various additives: fibre, hydrated lime and DBS polymer, were utilised in the porous asphalt. Comprehensive laboratory tests, including strength test, binder draindown test, Cantabro abrasion test, moisture susceptibility test, rutting test, thermal stress restrained sample test, and permeability test, were conducted. It is found that HVB significantly improved the overall performance of the porous asphalt; DBS additive improved its high-temperature performance, but lowered the cracking resistance at low temperature as well as the durability; fibre enhanced its durability and anti-cracking performance at low temperature; hydrated lime improved its moisture stability while weakening its durability. It is concluded that HVB and polyester fibre should be used in all porous asphalt; DBS additive is good for porous asphalt in high-temperature areas, and hydrated lime can be added to porous asphalt in rainy areas.
In-plant hot mix recycling technology has been widely used in maintenance and reconstruction due to its good recycling performance. However, the utilization rate of recycled asphalt pavement (RAP) is still only 10–25%, resulting in excessive accumulation and landfilling of RAP materials, which fails to promote the sustainable value of RAP in recycling. Therefore, this paper comprehensively explores the pavement performance of AC-20 ordinary asphalt recycled mixture and AC-13 modified asphalt recycled mixture with different proportions of RAP. The pavement performance test includes the dynamic modulus, rutting, dynamic creep, semicircular bending, and freeze-thaw splitting tests. The results show that, with the increase of RAP content, the mechanical properties and high-temperature properties of the two types of recycled asphalt mixtures are improved, the low temperature properties and moisture susceptibility properties are enhanced first and then weakened, and the best performance is reached when RAP content is 20 and 40%, respectively. According to the entire pavement performance test results, the influence of RAP content on AC-13 recycled modified asphalt mixtures is relatively smaller than that of AC-20 normal recycled asphalt mixtures. The addition of rejuvenator can improve the low-temperature performance and moisture susceptibility of recycled asphalt mixtures to a certain extent, especially for AC-20 ordinary recycled asphalt mixture. Consequently, it is suggested to use AC-13 recycled modified asphalt mixture in the upper layer of road; the RAP content can reach 20%, and rejuvenator can be used to improve its moisture susceptibility and low-temperature performance. AC-20 ordinary recycled asphalt mixture can be used in the middle surface layer, and the RAP content can reach 40%, or using AC-13 recycled modified asphalt mixture, the RAP content can reach 50%.
The compactability of an asphalt mixture is related to the heating temperature of the materials, but the heating temperature of reclaimed asphalt pavement (RAP) is limited by the production process of hot-in-plant recycled mixtures. To choose a reasonable heating temperature for RAP according to the compactability, the compaction energy ratio (CER) obtained from the Superpave gyratory compactor compaction curve was developed. The CERs of fourteen kinds of asphalt mixtures made with different RAPs were compared, all of which were different in type, content, and heating temperature. The results indicated that CER is an effective energy index to evaluate the workability of a bituminous mixture, and it considers both the accumulated energy after each gyration and the number of gyrations. It was also found that increasing the heating temperature of the RAP cannot always improve the workability of the recycled mixture, because the higher heating temperature caused more hard-aged bitumen to be blended with soft virgin bitumen during the mixing process. At the same RAP heating temperature, increasing the RAP content made it more difficult to compact the mixture, especially for RAPs with styrene–butadiene–styrene (SBS) modified bitumen, and the recycled mixtures with SBS-modified bitumen were more difficult to compact than those with nonmodified bitumen.
1 August 2020 in Construction and Building Materials
Water damage leads to spalling and loosening of asphalt pavement, which is ultimately due to a reduction in the bond strength of the asphalt mastic. The filler, as an important component of the asphalt mastic, has a great impact on the various properties of the asphalt mastic and even the asphalt mix itself. Therefore, it is important to study the influence of fillers on the performance of asphalt mastic. In this paper, the various properties of twelve types of fillers, including mineral powder, mineral powder partially replaced with cement, slaked lime, and recycled powder, and their effects on the bond strength of asphalt mastic are investigated. Binder bond strength (BBS) was used to evaluate the performance of the different asphalt mastics. The moisture resistance of the asphalt mastic was evaluated by measuring the bond strength of the asphalt mastic after treatment in a water bath. A grey correlation analysis was then carried out to derive the relationship between the filler index and the bond strength of the asphalt mastic. The results show that the addition of slaked lime and cement helped to improve the moisture resistance of the asphalt mastic. The fineness modulus and other indicators have a great influence on the bond strength of asphalt mastic. The interaction between hydrothermal coupling and filler type has a non-negligible effect on the moisture resistance of the asphalt mastic.