Walid Jomaa

Prof. Dr. Walid Jomaa


Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 April 2017 in Journal of Manufacturing Processes
Verified
Journal Article
Closed access
WJWalid Jomaa
Walid Jomaa
OMOussama Mechri
Oussama Mechri
JLJulie Lévesque
Julie Lévesque
VSVictor Songmene
Victor Songmene
PBPhilippe Bocher
Philippe Bocher
AGAugustin Gakwaya
Augustin Gakwaya

26 November 2014 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Closed access
PDF file
MDM. Daoud
M. Daoud
WJWalid Jomaa
Walid Jomaa
JCJ. F. Chatelain
J. F. Chatelain
ABA. Bouzid
A. Bouzid

10 June 2015 in Materials and Manufacturing Processes
Verified
Journal Article
Closed access
WJWalid Jomaa
Walid Jomaa
Victor SongmeneVictor Songmene
Victor Songmene
PBP. Bocher
P. Bocher
Excessive induction hardening treatment may result in deep-hardened layers, combined with tensile or low compressive residual stresses. This can be detrimental to the performance of mechanical parts. However, a judicious selection of the finishing process that possibly follows the surface treatment may overcome this inconvenience. In this paper, hard machining tests were performed to investigate the residual stresses and microstructure alteration induced by the machining of induction heat-treated AISI 4340 steel (58–60 HRC). The authors demonstrate the capacity of the machining process to enhance the surface integrity of induction heat-treated parts. It is shown how cutting conditions can affect the residual stress distribution and surface microstructure. On the one hand, when the cutting speed increases, the residual stresses tend to become tensile at the surface; and on the other hand, more compressive stresses are induced when the feed rate is increased. A microstructural analysis shows the formation of a thin white layer less than 2 µm and severe plastic deformations beneath the machined surface.

28 February 2014 in Materials
Verified
Journal Article
Open access
PDF file
WJWalid Jomaa
Walid Jomaa
Victor SongmeneVictor Songmene
Victor Songmene
PBPhilippe Bocher
Philippe Bocher
The surface finish was extensively studied in usual machining processes (turning, milling, and drilling). For these processes, the surface finish is strongly influenced by the cutting feed and the tool nose radius. However, a basic understanding of tool/surface finish interaction and residual stress generation has been lacking. This paper aims to investigate the surface finish and residual stresses under the orthogonal cutting since it can provide this information by avoiding the effect of the tool nose radius. The orthogonal machining of AA7075-T651 alloy through a series of cutting experiments was performed under dry conditions. Surface finish was studied using height and amplitude distribution roughness parameters. SEM and EDS were used to analyze surface damage and built-up edge (BUE) formation. An analysis of the surface topography showed that the surface roughness was sensitive to changes in cutting parameters. It was found that the formation of BUE and the interaction between the tool edge and the iron-rich intermetallic particles play a determinant role in controlling the surface finish during dry orthogonal machining of the AA7075-T651 alloy. Hoop stress was predominantly compressive on the surface and tended to be tensile with increased cutting speed. The reverse occurred for the surface axial stress. The smaller the cutting feed, the greater is the effect of cutting speed on both axial and hoop stresses. By controlling the cutting speed and feed, it is possible to generate a benchmark residual stress state and good surface finish using dry machining.

30 November 2019 in Materials
Verified
Journal Article
Open access
PDF file
MSMohamed Shnfir
Mohamed Shnfir
OOOluwole Olufayo
Oluwole Olufayo
WJWalid Jomaa
Walid Jomaa
Victor SongmeneVictor Songmene
Victor Songmene
Intermittent machining using ceramic tools such as hard milling is a challenging task due to the severe mechanical shock that the inserts undergo during machining and the brittleness of ceramic inserts. This study investigates the machinability of hardened steel AISI 1045 during face milling using SiAlON and whisker (SiCW) based ceramic inserts. The main focus seeks to identify the effects of cutting parameters, milling configuration, edge preparation and work material hardness on machinability indicators such as resultant cutting force, power consumption and flank tool wear. The effects of these varying cutting conditions on performance characteristics were investigated using a Taguchi orthogonal array design L32 (21 44) and evaluated using ANOVA. Results indicate lower resultant cutting forces were recorded with honed edge inserts of SiAlON ceramic grade. In addition, a decrease in resultant cutting forces was associated with reduced feed rates and increased hardness. The feed rate and cutting speed were also identified as the greatest influencing factors in the amount of cutting power. The main wear mechanisms responsible for flank wear on the ceramic inserts are micro-scale abrasion and micro-chipping. Increased flank wear was observed at low cutting speed and high feed rates, while micro-chipping mostly ensued from the cyclic loading of the radial tool edge form, which is more susceptible to impact fragmentation. Thus, the use of tools with chamfered tool-edge preparation greatly improved observed wear values. Additional confirmation tests were also conducted to validate the results of the tests.

15 January 2025 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Closed access
PDF file
ACAnuradha Colombathanthri
Anuradha Colombathanthri
WJWalid Jomaa
Walid Jomaa
YCYuvin Chinniah
Yuvin Chinniah