Hansong Li

Dr. Hansong Li

orcid

Research Focus & Metrics

Academic Career Length

14Years (2013-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
10 February 2013 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Closed access
PDF file
XFXiaoLong Fang
XiaoLong Fang
NQNingsong Qu
Ningsong Qu
HLHansong Li
Hansong Li
DZDi Zhu
Di Zhu

14 June 2017 in Scientific Reports
Verified
Journal Article
Open access
PDF file
HLHansong Li
Hansong Li
SNShen Niu
Shen Niu
QZQingliang Zhang
Qingliang Zhang
SFShuxing Fu
Shuxing Fu
NQNingsong Qu
Ningsong Qu
Electrochemical grinding (ECG) is a low-cost and highly efficient process for application to difficult-to-machine materials. In this process, the electrolyte supply mode directly affects machining stability and efficiency. This paper proposes a flow channel structure for an abrasive tool to be used for inner-jet ECG of GH4169 alloy. The tool is based on a dead-end tube with electrolyte outlet holes located in the sidewall. The diameter and number of outlet holes are determined through numerical simulation with the aim of achieving uniform electrolyte flow in the inter-electrode gap. Experiments show that the maximum feed rate and material removal rate are both improved by increasing the diamond grain size, applied voltage, electrolyte temperature and pressure. For a machining depth of 3 mm in a single pass, a feed rate of 2.4 mm min−1 is achieved experimentally. At this feed rate and machining depth, a sample is produced along a feed path under computer numerical control, with the feed direction changing four times. Inner-jet ECG with the proposed abrasive tool shows good efficiency and flexibility for processing hard-to-cut metals with a large removal depth.

13 October 2016 in Scientific Reports
Verified
Journal Article
Open access
HLHansong Li
Hansong Li
CGChuanping Gao
Chuanping Gao
GWGuoqian Wang
Guoqian Wang
NQNingsong Qu
Ningsong Qu
DZDi Zhu
Di Zhu
The titanium alloy Ti-6Al-4V is used in many industries including aviation, automobile manufacturing, and medical equipment, because of its low density, extraordinary corrosion resistance and high specific strength. Electrochemical machining (ECM) is a non-traditional machining method that allows applications to all kinds of metallic materials in regardless of their mechanical properties. It is widely applied to the machining of Ti-6Al-4V components, which usually takes place in a multicomponent electrolyte solution. In this study, a 10% NaNO3 solution was used to make multiple holes in Ti-6Al-4V sheets by through-mask electrochemical machining (TMECM). The polarization curve and current efficiency curve of this alloy were measured to understand the electrical properties of Ti-6Al-4V in a 10% NaNO3 solution. The measurements show that in a 10% NaNO3 solution, when the current density was above 6.56 A·cm−2, the current efficiency exceeded 100%. According to polarization curve and current efficiency curve, an orthogonal TMECM experiment was conducted on Ti-6Al-4V. The experimental results suggest that with appropriate process parameters, high-quality holes can be obtained in a 10% NaNO3 solution. Using the optimized process parameters, an array of micro-holes with an aperture of 2.52 mm to 2.57 mm and maximum roundness of 9 μm were produced using TMECM.

19 February 2014 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Closed access
PDF file
NQNingsong Qu
Ningsong Qu
XCXiaolei Chen
Xiaolei Chen
HLHansong Li
Hansong Li
DZDi Zhu
Di Zhu

23 April 2015 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Closed access
PDF file
XCXiaolei Chen
Xiaolei Chen
NQNingsong Qu
Ningsong Qu
HLHansong Li
Hansong Li

1 January 2022 in Journal of the Electrochemical Society
Verified
Journal Article
Closed access
XMXin Ma
Xin Ma
HLHansong Li
Hansong Li
XYXiaokang Yue
Xiaokang Yue
YYYitian Yang
Yitian Yang
LWLu Wang
Lu Wang
GXGuoliang Xu
Guoliang Xu
The application of titanium metal matrix composites (Ti-MMCs) in the aerospace industry has increased significantly owing to their excellent mechanical properties. However, these properties also make Ti-MMCs difficult to machine. Many problems can occur with traditional turning, such as tool damage and low efficiency remain. Electrochemical machining is not limited by the physical properties of metal materials, making it an ideal machining method for Ti-MMCs, but there have been few articles evaluating electrochemical turning (ECT) in this application. Therefore, the purpose of this study was to use a cathode tool with a rectangular end face to realize the ECT of particle reinforced Ti-MMCs. Parametric experiments were conducted by varying the machining voltage, workpiece rotation speed, electrolyte pressure, and axial offset to determine their effects on the intermittent feed ECT of a cylindrical workpiece. Finally, intermittent feed ECT was performed on the cylindrical surface with the preferred machining parameters, and a machining area with a circular arc area of 4124 mm 2 , an average radial removal depth of 1.19 mm, and an average circular arc radius of 42.44 mm was obtained on the cylindrical workpiece, which verified the practical performance of the intermittent feed ECT method for machining titanium matrix composites.