The impact of the pandemic of COVID-19 has a certain influence on various walks of life around the world. Because of the pandemic of this novel coronavirus in terms of COVID-19, the social life global wide has been changed a lot. To keep the social distance between human being to prevent from being infected is the most important strategy for all the countries. Many dental schools have been locked down to minimize the spread out of this coronavirus infection. Close contact between human being are required for all those learning process in traditional dental education. Learning methods should be innovated to keep on the learning process but away from being infected for dental education during pandemic. The purpose of this manuscript is to exchange the information and experience of those dental educators from different countries to prepare for the future demand for dental education during pandemic. By means of three online symposiums, dental educators from different countries were invited to give presentation and discussion regarding to the information and experience in the innovation of dental education during the pandemic. The results showed that the impact of the pandemic of COVID-19 affects the dental education a lot. Intelligent technology has certain benefit for the learning process of dental education during the pandemic. The impact of the pandemic of COVID-19 affects dental education a lot. The model of dental education should be innovated to suit different situations and novelty intelligent technology should be applied for future dental education.

The purpose of this study was to evaluate the abrasive wear and surface roughness of 20 currently available commercial dental composite resins, including nanofilled, supra-nanofilled, nanohybrid and microhybrid composite resins. The volume loss, maximum vertical loss, surface roughness (Ra) and surface morphology [Scanning electron microscopy (SEM)] were determined after wear. The inorganic filler content was determined by thermogravimetric analysis. The result showed that the volume loss and vertical loss varied among the materials. The coefficients of determination (R2) of wear volume loss and filler content (wt%) was 0.283. SEM micrographs revealed nanofilled composites displayed a relatively uniform wear surfaces with nanoclusters protrusion, while the performance of nanohybrid composites varied. The abrasive wear resistance of contemporary dental composite resins is materialdependent and cannot be deduced from its category, filler loading and composite matrix; The abrasive wear resistance of some flowable composites is comparable to the universal/posterior composite resins.

Online learning has been utilized in the world to continue educational activities in dentistry, which was severely affected by the pandemic of coronavirus disease 2019 (COVID-19). The purpose of this study was aimed to evaluate the effect of online learning during the pandemic of COVID-19 in different dental schools of different countries in Asia by the questionnaire survey. Mantel-Haenszel chi-square tests were used to analyze the difference between dental schools with and without shutdown. A questionnaire-based online survey was used to evaluate the online learning effect on undergraduate students in 13 dental schools of 7 Asia countries and regions. For the question that blended learning class has better learning efficiency, the agreement rate was significantly higher in the students (80.3%) from the dental schools that did not suspend face-to-face education activities than in the students (50.3%) from the dental school that was shut down. Within the limitation of this study, it is concluded that a combination of physical and online classes in terms of blended learning courses will be the future trend for dental education.

Hydrogel is a polymer matrix containing a large amount of water. It is similar to extracellular matrix components. It comes into contact with blood, body fluids, and human tissues without affecting the metabolism of organisms. It can be applied to bone and cartilage tissues. This article introduces the high-strength polymer hydrogel and its modification methods to adapt to the field of bone and cartilage tissue engineering. From the perspective of the mechanical properties of hydrogels, the mechanical strength of hydrogels has experienced from the weak-strength traditional hydrogels to the high-strength hydrogels, then the injectable hydrogels were invented and realized the purpose of good fluidity before the use of hydrogels and high strength in the later period. In addition, specific methods to give special physical properties to the hydrogel used in the field of bone and cartilage tissue engineering will also be discussed, such as 3D printing, integrated repair of bone and cartilage tissue, bone vascularization, and osteogenesis hydrogels that regulate cell growth, antibacterial properties, and repeatable viscosity in humid environments. Finally, we explain the main reasons and contradictions in current applications, look forward to the research prospects in the field of bone and cartilage tissue engineering, and emphasize the importance of conducting research in this field to promote medical progress.

This review examined the efficacy of surface treatments and adhesive monomers for enhancing zirconia-resin bond strength. A comprehensive literature search in PubMed, Embase, Web of Science, Scopus, and the Cochrane Library yielded relevant in vitro studies. Employing pairwise and Bayesian network meta-analyses, 77 articles meeting inclusion criteria were analyzed. Gas plasma was found to be ineffective, while treatments including air abrasion, silica coating, laser, selective infiltration etching, hot etching showed varied effectiveness. Air abrasion with finer particles (25–53 µm) showed higher immediate bond strength than larger particles (110–150 µm), with no significant difference post-aging. The Rocatec silica coating system outperformed the CoJet system in both immediate and long-term bond strength. Adhesives containing 10-methacryloyloxydecyl dihydrogen phosphate (10-MDP) were superior to other acidic monomers. The application of 2-hydroxyethyl methacrylate and silane did not improve bonding performance. Notably, 91.2 % of bonds weakened after aging, but this effect was less pronounced with air abrasion or silica coating. The findings highlight the effectiveness of air abrasion, silica coating, selective infiltration etching, hot etching, and laser treatment in improving bond strength, with 10-MDP in bonding agents enhancing zirconia bonding efficacy.