A novel rigid sound-absorbing material made from used palm oil-based polyurethane foam (PUF) and water hyacinth fiber (WHF) composite was developed in this research. The NCO index was set at 100, while the WHF content was set at 1%wt with mesh sizes ranging from 80 to 20. The mechanical properties, the morphology, the flammability, and the sound absorption coefficient (SAC) of the PUF composite were all investigated. When the WHF size was reduced from 80 to 20, the compression strength of the PUF increased from 0.33 to 0.47 N/mm². Furthermore, the use of small fiber size resulted in a smaller pore size of the PUF composite and improved the sound absorption and flammability. A feasible sound-absorbing material was a PUF composite with a WHF mesh size of 80 and an SAC value of 0.92. As a result, PUF derived from both water hyacinth and used palm oil could be a promising green alternative material for sound-absorbing applications.

The anionic water-insoluble cyclodextrin polymer (polyCTR-β-CD) was crosslinked between β-cyclodextrin (β-CD) and citric acid (CTR) at 180 °C during 30 minutes to eliminate paraquat (PQ) from water. The reaction yield was equal to 70.2%, the ionic exchange capacity corresponded to 3.29 mmol·g⁻¹ and the β-CD content was 0.29 mmol·g⁻¹. Then, samples were characterized by SEM, ATR-FTIR, TGA, BET and stereoscopic microscope. Adsorption experiments were investigated with different factors such as pH of the solution, contact time, initial concentration of paraquat and adsorption temperature. The relevant pH was equal to 6.5 and the optimal contact time was 120 minutes to attain adsorption equilibrium. At 30 °C, the adsorption capacity was increased (9.4, 17.4 and 20.8 mg·g⁻¹) when the initial concentration of paraquat was raised (25, 50 and 200 mg·L⁻¹ respectively). Adsorption kinetics was appropriated to the pseudo-second-order model and adsorption isotherm was fitted to the Langmuir model. For thermochemistry parameters at different temperatures, the negative ΔG° showed a spontaneous adsorption process, the negative ΔH° indicated an exothermic process and the positive ΔS° exhibited an increase disorder. Finally, the reusability of the insoluble polymer was reached 78.3% after four regeneration cycles in methanol.

The contamination of hydrosoluble pesticides in water could generate a serious problem for biotic and abiotic components. The removal of a hazardous agrochemical (paraquat) from water was achieved by adsorption processes using poly(vinyl alcohol)-cyclodextrin nanosponges, which were prepared with various formulations via the crosslinking between citric acid and β-cyclodextrin in the presence of poly(vinyl alcohol). The physicochemical properties of nanosponges were also characterized by different techniques, such as gravimetry, thermogravimetry, microscopy (SEM and Stereo), spectroscopy (UV-visible, NMR, ATR-FTIR, and Raman), acid-base titration, BET surface area analysis, X-ray diffraction, and ion exchange capacity. The C10D-P2 nanosponges displayed 60.2% yield, 3.14 mmol/g COOH groups, 0.335 mmol/g β-CD content, 96.4% swelling, 94.5% paraquat removal, 0.1766 m² g⁻¹ specific surface area, and 5.2 × 10⁻⁴ cm³ g⁻¹ pore volume. The presence of particular peaks referring to specific functional groups on spectroscopic spectra confirmed the successful polycondensation on the reticulated nanosponges. The pseudo second-order model (with R² = 0.9998) and Langmuir isotherm (with R² = 0.9979) was suitable for kinetics and isotherm using 180 min of contact time and a pH of 6.5. The maximum adsorption capacity was calculated at 112.2 mg/g. Finally, the recyclability of these nanosponges was 90.3% of paraquat removal after five regeneration times.

Pretreatment is a crucial process in a lignocellulosic biorefinery. Corncob is typically considered as a natural renewable carbon source to produce various bio-based products. This study aimed to evaluate the performance of the hydrothermal-mechanical pretreatment of corncob for biofuels and biochemical production. Corncob was first pretreated by liquid hot water (LHW) at different temperatures (140–180 °C) and duration (30, 60 min) and then subjected to centrifugal milling to produce bio-powders. To evaluate the performance of this combined pretreatment, the energy efficiency and waste generation were investigated. The results indicated that the maximum fermentable sugars (FS) were 0.488 g/g biomass obtained by LHW at 180 °C, 30 min. In order to evaluate the performance of this combined pretreatment, the energy efficiency and waste generation were 28.3 g of FS/kWh and 7.21 kg of waste/kg FS, respectively. These obtained results indicate that the combined hydrothermal-mechanical pretreatment was an effective pretreatment process to provide high energy efficiency and low waste generation to produce biofuels. In addition, the energy efficiency and waste generation will be useful indicators for process scaling-up into the industrial scale. This combined pretreatment could be a promising pretreatment technology for the production of biofuels and biochemicals from lignocellulosic valorization.