This paper presents a differential synthetic aperture radar (SAR) interferometry (DIFSAR) approach for investigating deformation phenomena on full-resolution DIFSAR interferograms. In particular, our algorithm extends the capability of the small-baseline subset (SBAS) technique that relies on small-baseline DIFSAR interferograms only and is mainly focused on investigating large-scale deformations with spatial resolutions of about 100/spl times/100 m. The proposed technique is implemented by using two different sets of data generated at low (multilook data) and full (single-look data) spatial resolution, respectively. The former is used to identify and estimate, via the conventional SBAS technique, large spatial scale deformation patterns, topographic errors in the available digital elevation model, and possible atmospheric phase artifacts; the latter allows us to detect, on the full-resolution residual phase components, structures highly coherent over time (buildings, rocks, lava, structures, etc.), as well as their height and displacements. In particular, the estimation of the temporal evolution of these local deformations is easily implemented by applying the singular value decomposition technique. The proposed algorithm has been tested with data acquired by the European Remote Sensing satellites relative to the Campania area (Italy) and validated by using geodetic measurements.

In this paper, an advanced technique for the generation of deformation maps using synthetic aperture radar (SAR) data is presented. The algorithm estimates the linear and nonlinear components of the displacement, the error of the digital elevation model (DEM) used to cancel the topographic terms, and the atmospheric artifacts from a reduced set of low spatial resolution interferograms. The pixel candidates are selected from those presenting a good coherence level in the whole set of interferograms and the resulting nonuniform mesh tessellated with the Delauney triangulation to establish connections among them. The linear component of movement and DEM error are estimated adjusting a linear model to the data only on the connections. Later on, this information, once unwrapped to retrieve the absolute values, is used to calculate the nonlinear component of movement and atmospheric artifacts with alternate filtering techniques in both the temporal and spatial domains. The method presents high flexibility with respect to the required number of images and the baselines length. However, better results are obtained with large datasets of short baseline interferograms. The technique has been tested with European Remote Sensing SAR data from an area of Catalonia (Spain) and validated with on-field precise leveling measurements.

In this paper, the recently developed multiplicative regularized contrast source inversion method is applied to microwave biomedical applications. The inversion method is fully iterative and avoids solving any forward problem in each iterative step. In this way, the inverse scattering problem can efficiently be solved. Moreover, the recently developed multiplicative regularizer allows us to apply the method blindly to experimental data. We demonstrate inversion from experimental data collected by a 2.33-GHz circular microwave scanner using a two-dimensional (2-D) TM polarization measurement setup. Further some results of a feasibility study of the present inversion method to the 2-D TE polarization and the full-vectorial three-dimensional measurement will be presented as well.

Radar data have already proven to be compressible with no significant losses for most of the applications in which it is used. In the framework of information theory, the compressibility of a signal implies that it can be decomposed onto a reduced set of basic elements. Since the same quantity of information is carried by the original signal and its decomposition, it can be deduced that a certain degree of redundancy exists in the explicit representation. According to the theory of compressive sensing (CS), due to this redundancy, it is possible to infer an accurate representation of an unknown compressible signal through a highly incomplete set of measurements. Based on this assumption, this paper proposes a novel method for the focusing of raw data in the framework of radar imaging. The technique presented is introduced as an alternative option to the traditional matched filtering, and it suggests that the new modes of acquisition of data are more efficient in orbital configurations. In this paper, this method is first tested on 1-D simulated signals, and results are discussed. An experiment with synthetic aperture radar (SAR) raw data is also described. Its purpose is to show the potential of CS applied to SAR systems. In particular, we show that an image can be reconstructed, without the loss of resolution, after dropping a large percentage of the received pulses, which would allow the implementation of wide-swath modes without reducing the azimuth resolution.

Carrying out an effective control of fishing activities is essential to guarantee a sustainable exploitation of sea resources. Nevertheless, as the regulated areas are extended, they are difficult and time consuming to monitor by means of traditional reconnaissance methods such as planes and patrol vessels. On the contrary, satellite-based synthetic aperture radar (SAR) provides a powerful surveillance capability allowing the observation of broad expanses, independently from weather effects and from the day and night cycle. Unfortunately, the automatic interpretation of SAR images is often complicated, even though undetected targets are sometimes visible by eye. Attending to these particular circumstances, a novel approach for ship detection is proposed based on the analysis of SAR images by means of the discrete wavelet transform. The exposed method takes advantage of the difference of statistical behavior among the ships and the surrounding sea, interpreting the information through the wavelet coefficients in order to provide a more reliable detection. The analysis of the detection performance over both simulated and real images confirms the robustness of the proposed algorithm.