In the present article, a highly heat-resistant composite with a high fiber volume fraction ( Vf > 60%) was successfully manufactured using engineering plastic Nylon66 as matrix and carbon fabric as reinforcement by a solution impregnation molding method. The mechanical properties of the composite were investigated using a tensile measuring device. Mechanical analysis revealed the superior mechanical properties of the composite relative to those of previously reported carbon fiber-reinforced thermoplastics (CFRTPs). The cross section and fracture surface of the composite were characterized by scanning electron microscopy. The resin successfully impregnated the fiber bundles and the bonding strength of the fiber–resin interface was excellent. Dynamic mechanical analysis was used to evaluate the heat-resistant property of the composite. The composite exhibited a better heat-resistant property relative to that of the carbon fiber-reinforced crystalline co-polyester composite. To further verify the versatility of this method, super engineering plastic polyetherimide with a higher molecular weight was successfully employed as matrix to prepare CFRTP.
Fiber-reinforced plastic (FRP) is composed of reinforced fibers and matrix resin, and has high specific strength and low-density materials. Because of the orientation of the fibers within them, FRPs are prone to buckling damage when under compression along the axial direction of the fiber, especially flexible organic ones. The compressive performance of FRP is largely dependent on fiber properties. the buckling load of FRP will increase with the increasing of fiber’s. In this study, we developed a way to improve the compressive and bending strength of ultra-high molecular weight polyethylene (UHMWPE) fibers. Carbon nanotubes (CNTs) and vapor-grown carbon fibers (VGCFs) were coated on the surface of UHMWPE fibers by pyrrole vapor deposition. The transverse compressive strength and bending strength of single UHMWPE fibers were determined by microcompression and single fiber bending measurements, respectively. The experiment result showed that coating UHMWPE fibers with CNTs and VGCFs increased both their transverse compressive strength and bending strength. It is excepted that the improved fiber would applied in FRP for better compressive performance.
Sandwich-structure materials consist of a high-strength skin material and a lightweight core material. The advantages of sandwich structures are known to include excellent mechanical properties and low weight. Sandwich structures are lightweight because of their lightweight core; meanwhile, the skin structure provides mechanical strength and bears bending stress. Carbon-fiber-reinforced plastic (CFRP) is a high-specific-strength and high-specific-rigidity material. In recent years, CFRP sandwich structures have been used in aerospace applications due to their lightweight properties. However, soft-core members such as plastic foam materials have low rigidity and therefore may not exhibit adequate function as a sandwich structure. Webs can make up for the lack of rigidity of soft core members. Consequently, sandwich structures with reinforcement webs offer higher strength than sandwich structures without reinforcement webs. This study focused on reinforcement webs suitable for use in CFRP sandwich structures by evaluating the bending characteristics of CFRP sandwich structures with reinforcement webs. Experimental results demonstrated that CFRP sandwich structures with reinforcement webs had improved bending strength. The effects of the spacing interval of reinforcement webs and the number of layers of carbon fiber fabric on the bending characteristics of CFRP sandwich structures were also examined. Finally, an optimal condition model was created for CFRP sandwich structures with reinforcement webs.
Carbon fiber reinforced plastics (CFRPs) are widely used in the aerospace, automotive, and construction industries. CFRP prepregs (intermediate products) are generally used in CFRP production, with a large number of prepreg cut‐offs being discarded during cutting processes. There is strong demand for a method for recycling carbon fiber prepreg cut‐offs. This paper proposes a method for recycling such material, which is characterized by low cost and high added value, in order to foster the development of a recycling‐oriented society. We prepare carbon tapes (CTs) by cutting discarded cut‐offs according to their size so as to maximize fiber length. Using a simple water CT dispersion method, we fabricate uniform CT sheets and mold a recycled CT‐reinforced composite (R‐CT‐RC). Sample prototyping and mechanical characteristic testing indicate that this R‐CT‐RC is characterized by low recycling cost and desirable mechanical properties. Recycled CT‐reinforced composite with thermoplastic (R‐CT‐RC/TP), which is prepared by adding thermoplastic resin between CTs, can be re‐molded and therefore readily re‐recycled.