The issues of monitoring and fault diagnosis of drives with permanent magnet synchronous motors (PMSMs) are currently very relevant because of the increasing use of these drives in safety-critical devices. Every year, more and more articles are published on this subject. Therefore, the objective of this article is to update the overview of diagnostic methods and techniques for PMSM drives. Each of the main chapters of the article focuses on a specific element of the drive system (motor, power converter, measuring sensors), with particular emphasis on the components of the motor (stator windings, magnets, bearings, and rotor). The main sections on PMSM fault diagnosis are divided according to the type of methods used to obtain the symptoms of the damage. In addition, a review of methods that use the analysis of signals of the control structure for the diagnosis of damage to a vector-controlled motor is presented, as well as the latest achievements of researchers in the field of shallow and deep neural networks for the detection and classification of failures of PMSM drives. Based on the analyses presented in the literature, some development trends and challenges related to the development of diagnostics and fault-tolerant control of PMSM drives are discussed in the conclusion part.
Permanent magnet synchronous motors (PMSMs) are becoming more popular, both in industrial applications and in electric and hybrid vehicle drives. Unfortunately, like the others, these are not reliable drives. As in the drive systems with induction motors, the rolling bearings can often fail. This paper focuses on the possibility of detecting this type of mechanical damage by analysing mechanical vibrations supported by shallow neural networks (NNs). For the extraction of diagnostic symptoms, the Fast Fourier Transform (FFT) and the Hilbert transform (HT) were used to obtain the envelope signal, which was subjected to the FFT analysis. Three types of neural networks were tested to automate the detection process: multilayer perceptron (MLP), neural network with radial base function (RBF), and Kohonen map (self-organizing map, SOM). The input signals of these networks were the amplitudes of harmonic components characteristic of damage to bearing elements, obtained as a result of FFT or HT analysis of the vibration acceleration signal. The effectiveness of the analysed NN structures was compared from the point of view of the influence of the network architecture and various parameters of the learning process on the detection effectiveness.
In this article, a low-cost computer system for the monitoring and diagnosis of the condition of the induction motor (IM) rolling bearings is demonstrated and tested. The system allows the on-line monitoring of the IM bearings and subsequent fault diagnostics based on analysis of the vibration measurement data. The evaluation of the bearing condition is made by a suitably trained neural network (NN), on the basis of the spectral and envelope analysis of the mechanical vibrations. The system was developed in the LabVIEW environment in such a way that it could be run on any PC. The functionality of the application has been tested on a real object. The study was conducted on a low-power IM equipped with a set of specially prepared bearings so as to model the different damages. In the designed computer system, a selected NN for detecting and identifying the defects of individual components of the induction motor’s bearings was implemented. The training data for NNs were obtained from real experiments. The magnitudes of the characteristic harmonics, obtained from the spectral analysis and the envelope analysis, were used for training and testing the developed neural detectors based on Matlab toolbox. The experimental test results of the developed monitoring and diagnosis system are presented in the article. The evaluation of the system’s ability to detect and identify the defects of individual components of bearings, such as the rolling element, and outer race and inner race, was made. It was also shown that the developed NN-based detectors are insensitive to other motor faults, such as short-circuits of the stator winding, broken rotor bars or motor misalignment.
Mechanical unbalance is a phenomenon that concerns rotating elements, including rotors in electrical machines. An unbalanced rotor generates vibration, which is transferred to the machine body. The vibration contributes to reducing drive system reliability and, as a consequence, leads to frequent downtime. Therefore, from an economic point of view, monitoring the unbalance of rotating elements is justified. In this paper, the rotor unbalance of a drive system with a permanent magnet synchronous motor (PMSM) was physically modelled using a specially developed shield, with five test masses fixed at the motor shaft. The analysed diagnostic signal was mechanical vibration. Unbalance was detected using selected signal analysis methods, such as frequency-domain methods (classical spectrum analysis FFT and a higher-order bispectrum method) and two methods applied in technical diagnostics (order analysis and orbit method). The efficiency of unbalance symptom detection using these four methods was compared for the frequency controlled PMSM. The properties of the analysed diagnostic methods were assessed and compared in terms of their usefulness in rotor unbalance diagnosis, and the basic features characterizing the usefulness of these methods were determined depending on the operating conditions of the drive. This work could have a significant impact on the process of designing diagnostic systems for PMSM drives.
29 July 2023 in Eksploatacja i Niezawodność – Maintenance and Reliability
Equipment condition monitoring is essential to maintain the reliability of the electromechanical systems. Recently topics related to fault diagnosis have attracted significant interest, rapidly evolving this research area. This study presents a non-invasive method for online state classification of a squirrel-cage induction motor. The solution utilizes thermal imaging for non-contact analysis of thermal changes in machinery. Moreover, used convolutional neural networks (CNNs) streamline extracting relevant features from data and malfunction distinction without defining strict rules. A wide range of neural networks was evaluated to explore the possibilities of the proposed approach and their outputs were verified using model interpretability methods. Besides, the top-performing architectures were optimized and deployed on resource-constrained hardware to examine the system's performance in operating conditions. Overall, the completed tests have confirmed that the proposed approach is feasible, provides accurate results, and successfully operates even when deployed on edge devices.
This article presents the effectiveness of bispectrum analysis for the detection of the rotor unbalance of an induction motor supplied by the mains and a frequency converter. Two diagnostic signals were analyzed, as well as the stator current and mechanical vibrations of the tested motors. The experimental tests were realized for two low-power induction motors, with one and two pole pairs, respectively. The unbalance was modeled using a test mass mounted on a specially prepared disc and directly on the rotor and the influence of this unbalance location was tested and discussed. The results of the bispectrum analysis are compared with results of Fourier transform and the effectiveness of unbalance detection are discussed and compared. The influence of the registration time of the analyzed signal on the quality of fault symptom analyses using both transforms was also tested. It is shown that the bispectrum analysis provides an increased number of fault symptoms in comparison with the classical spectral analysis as well as it is not sensitive to a shorter registration time of the diagnostic signals.