Additive manufacturing (AM) is an attractive set of processes that are being employed lately to process specific materials used in the fabrication of electrical machine components. This is because AM allows for the preservation or enhancement of their magnetic properties, which may be degraded or limited when manufactured using other traditional processes. Soft magnetic materials (SMMs), such as Fe–Si, Fe–Ni, Fe–Co, and soft magnetic composites (SMCs), are suitable materials for electrical machine additive manufacturing components due to their magnetic, thermal, mechanical, and electrical properties. In addition to these, it has been observed in the literature that other alloys, such as soft ferrites, are difficult to process due to their low magnetization and brittleness. However, thanks to additive manufacturing, it is possible to leverage their high electrical resistivity to make them alternative candidates for applications in electrical machine components. It is important to highlight the significant progress in the field of materials science, which has enabled the development of novel materials such as high-entropy alloys (HEAs). These alloys, due to their complex chemical composition, can exhibit soft magnetic properties. The aim of the present work is to provide a critical review of the state-of-the-art SMMs manufactured through different AM technologies. This review covers the influence of these technologies on microstructural changes, mechanical strengths, post-processing, and magnetic parameters such as saturation magnetization (M_S), coercivity (H_C), remanence (B_r), relative permeability (M_r), electrical resistivity (r), and thermal conductivity (k).

In this paper, the best laser powder bed fusion (L-PBF) printing conditions for FeSi steels with two different Si content (3.0% and 6.5%) are defined. Results show very strict processing window parameters, following a lack of fusion porosity at low specific energy values and keyhole porosity in correspondence with high specific energy values. The obtained microstructure consists of grains with epitaxial growth starting from the grains already solidified in the underling layer. This allows the continuous growth of the columnar grains, directed parallel to the built direction of the component. The magnetic behaviour of FeSi6.5 samples, although the performances found do not still fully reach those of the best commercial electrical steels (used to manufacture magnetic cores of electrical machines and other similar magnetic components), appears to be quite promising. An improvement of the printing process to obtain thin sheets with increased Si content, less than 0.5 mm thick, with accurate geometry and robust structures, can result to an interesting technology for specific application where complex geometries and sophisticated shapes are required, avoiding mechanical machining processes for electrical steel with high silicon content.

Additive manufacturing technology like laser powder bed fusion represents a valid alternative for the production of ferromagnetic cores. In this study, two grades of steel were considered, with standard (3.0 wt%) and high (6.5 wt%) Si content. The study is aimed at optimizing the process parameters in order to obtain components suitable for magnetic applications. Moreover, the effect of post-production annealing heat treatment on the microstructure evolution is investigated. The investigation included microstructural analysis by optical microscope, dynamic scanning calorimetry analysis and electro-magnetic measurements on samples with optimized geometry. Results shows that both types of steel can be produced free from defects. Even if the magnetic behaviour of FeSi6.5 samples by AM do not fully reproduces that obtained on electrical steels manufactured by standard process, it appears quite promising. In this framework the optimization of post-production processes represents a promising challenge to meet market demands. Graphical abstract

The rapidly ascending trend of additive manufacturing techniques requires a tailoring of existing solidification models and the development of new numerical tools. User-friendly numerical models can be a valid aid in order to optimize operating parameter ranges with the scope to extend the modelling tools to already existing or innovative alloys. In this paper a modelling approach is described simulating the generation of single tracks on a powder bed system in a selective laser melting process. The approach we report attains track geometry as a function of: alloy thermo-physical properties, laser speed and power, powder bed thickness. Aim of the research is to generate a numerical tool able to predict laser power and speed ranges in manufacturing porosity-free printed parts without lack of fusion and keyhole pores. The approach is based on a simplified description of the physical aspects. Main simplifications concern: the laser energy input, the formation of the pool cavity, and the powder bed thermo-physical properties. The model has been adjusted based on literature data providing the track’s geometry (width and depth) and relative density. Such data refer to different alloys. In particular, Ti6Al4V, Inconel625, Al7050, 316L and pure copper are considered. We show that the printing process presents features common to all alloys. This allows the model to predict the printing behavior of an alloy from its physical properties, avoiding the need to perform specific experimental activities.

Currently, the commercial production of ferromagnetic cores involves staking thin sheets of soft magnetic material, alternating with dielectric material to reduce the eddy current losses. High silicon FeSi steels show excellent soft magnetic properties. Anyway, their workability decreases Si content increases thus imposing a technological limit in the production of thin sheets up to 3.5–4% Si. The additive manufacturing (AM) process based on laser powder bed fusion (L-PBF) offers the possibility to redesign the magnetic components, compared to conventional design, allowing to act on the chemical composition of magnetic materials and on the geometry of the components. In the case of FeSi alloys, the additive technology allows to overcome the limit of Si content opening new perspectives for the production of ferromagnetic cores with high magnetic performance. In this work the feasibility study on the production of FeSi magnetic steel components by L-PBF technology is reported. Two variants of FeSi steels, with Si content of 3.0 wt.% and 6.5 wt.%, were considered. The effect of process parameters on the densification of manufactured parts was investigated. The best operating window has been identified for both steel chemical compositions, in terms of laser scan speed and power.