In order to realize a premixed compression ignition (PCI) engine by utilization of bio-alcohol, combustion characteristics of bio-alcohol blended with gas oil were compared between ethanol and n-butanol in a diesel engine. The effects of the ethanol blend ratio and the butanol blend ratio on ignition delay, premixed combustion, diffusion combustion, fuel consumption and exhaust emissions such as smoke density and NOx were investigated experimentally. It is found that ethanol almost burns out together with combustion of low evaporation temperature composition of gas oil in the premixed combustion period and the heat release in the diffusion combustion is based on mainly high evaporation temperature composition of gas oil, then, soot is formed in the diffusion combustion of gas oil. On the other hand, a part of butanol burns in the diffusion combustion, however, the combustion of butanol in the diffusion stage is not the cause of soot formation. Butanol is more useful in comparison with ethanol because butanol can be blended with gas oil without surface-active agent, and fuel consumption and smoke are almost equal in both blend fuels if the alcohol blend ratio is the same.
1 September 2015 in SAE International Journal of Advances and Current Practices in Mobility
Measurements of temporal and spatial changes in the velocity and size of droplets of diesel fuel sprays under two injection pressures were conducted near the nozzle orifice by a laser 2-focus velocimeter (L2F). The result showed that the size of droplets under higher rail pressure was larger than that under lower rail pressure at the spray center and was smaller than that under lower rail pressure at the spray periphery. It was found that the size of droplets deceased in the downstream direction of the spray and the decrease rate increased with the rail pressure. The cross-sectional average velocity increased and the cross-sectional average size decreased with the rail pressure in the spray near the nozzle exit.
High pressure injection systems have essential roles in realizing highly controllable fuel injections in internal combustion engines. The primary atomization processes in the near field of the spray, and even inside the injector, determine the subsequent spray development with a considerable impact on the combustion and pollutant formation. Therefore, the processes should be understood as much as possible; for instance, to develop mathematical and numerical models. However, the experimental difficulties are extremely high, especially near the injector nozzle or inside the nozzle, due to the very small geometrical scales, the highly concentrated optical dense spray processes and the high speed and drastic transient nature of the spray. In this study, several unique and partly recently developed techniques are applied for detailed measurements on the flow inside the nozzle and the spray development very near the nozzle. As far as possible, the same three-hole injector for high pressure diesel injection is used to utilize and compare different measurement approaches. In a comprehensive section, the approach is taken to discuss the measurement results in comparison. It is possible to combine the observations within and outside the injector and to discuss the entire spray development processes for high pressure diesel sprays. This allows one to confirm theories and to provide detailed and, in parts, even quantitative data for the validation of numerical models.
A laser 2-focus velocimeter (L2F) has been applied for measurements of velocity and size of droplets of diesel spray and an evaluation method of mass flow rate has been proposed. The L2F has a micro-scale probe which consists of two foci. The distance between two foci is 17μm. The data acquisition rate of the L2F has been increased to 15MHz in order to capture every droplet which appears in the measurement volume. The diesel fuel spray injected intermittently into the atmosphere was investigated. The orifice diameter of the injector nozzle was 0.113mm. The injection pressure was set at 40MPa by using a common rail system. Measurements were conducted on ten planes 5 to 25mm downstream from the nozzle exit. It was clearly shown that the velocity of droplet was the highest at the spray center. The size of droplet at the spray center decreased downstream within 15mm from the nozzle exit. The mass flow rate near the spray center was found to be larger than that in the spray periphery region. It was confirmed that the fuel mass per injection evaluated by the proposed method based on the L2F measurement was near to the injected mass in a plane further than 15mm from the nozzle exit. However, fuel mass was underestimated in a plane closer to the nozzle exit. The probability density of infinitesimal distance between surfaces of adjacent droplets increased remarkably near the spray center 5 and 12mm downstream from the nozzle exit. As infinitesimal distance can be thought as an indicator of a highly dense region, it is understood that underestimation of fuel mass near the nozzle exit is due to the highly dense region. The diameter of the region, where the highly dense region was observed, was estimated as an order of 0.2mm in a plane 5mm downstream from the nozzle.
1 January 2015 in Journal of Thermal Science and Technology