New N‐allyl/propargyl 4‐substituted 1,2,3,4‐tetrahydroquinolines derivatives were efficiently synthesized using acid‐catalyzed three components cationic imino Diels–Alder reaction (70–95%). All compounds were tested in vitro as dual acetylcholinesterase and butyryl‐cholinesterase inhibitors and their potential binding modes, and affinity, were predicted by molecular docking and binding free energy calculations (∆G) respectively. The compound 4af (IC₅₀ = 72 μm) presented the most effective inhibition against acetylcholinesterase despite its poor selectivity (SI = 2), while the best inhibitory activity on butyryl‐cholinesterase was exhibited by compound 4ae (IC₅₀ = 25.58 μm) with considerable selectivity (SI = 0.15). Molecular docking studies indicated that the most active compounds fit in the reported acetylcholinesterase and butyryl‐cholinesterase active sites. Moreover, our computational data indicated a high correlation between the calculated ∆G and the experimental activity values in both targets.

In industry, silica nanoparticles (NPs) are obtained by the fuming and the precipitation method. Fumed silica NPs are commonly used in the preparation of nanocomposites because they have an extremely low bulk density (160–190 kg/m³), large surface area (50–600 m²/g), and nonporous surface, which promotes strong physical contact between the NPs and the organic phase. Fumed silica has fewer silanol groups (Si–OH) on its surface than the silica prepared by the Stöber method. However, the number of –OH groups on the fumed silica surface can be increased by pretreating them with sodium hydroxide (NaOH) before further surface modification. In this study, the effectiveness of the NaOH pretreatment was evaluated on commercial fumed silica NPs with a surface area of 200 m²/g. The number of surface –OH groups was estimated by potentiometric titration. The pretreated fumed NPs, and the precipitated NPs (prepared by the Stöber method) were modified with 3-aminopropyltriethoxysilane (APTES) to obtain A200S and nSiO₂-APTES, respectively. The NPs were characterized using electron dispersive scanning (EDS), scanning electron microscopy (SEM), dynamic light scattering (DLS), Fourier transform infrared spectroscopy (FT-IR), thermogravimetric analysis (TGA), X-ray diffraction (XRD), BET (Brunauer–Emmett–Teller) analysis, and ζ-potential. XRD confirmed the presence of the organo-functional group on the surface of both NPs. After the amino-functionalization, the ζ-potential values of the nSiO₂ and A200 changed from −35.5 mV and −14.4 mV to +26.2 mV and +11.76 mV, respectively. Consequently, we have successfully synthesized functionalized NPs with interesting, specific surface area and porosity (pore volume and size), which can be attractive materials for chemical and energy industries.

In this study, a set of advanced characterization techniques were used to evaluate the morphological, structural, and thermal properties of a novel molecular hybrid based on silica nanoparticles/hydrolyzed polyacrylamide (CSNH-PC1), which was efficiently obtained using a two-step synthetic pathway. The morphology of the nanohybrid CSNH-PC1 was determined using scanning electron microscopy (SEM), dynamic light scattering (DLS), and nanotracking analysis (NTA) techniques. The presence of C, N, O, and Si atoms in the nanohybrid structure was verified using electron dispersive scanning (EDS). Moreover, the corresponding structural analysis was complemented using powder X-ray diffraction (XRD) and attenuated total reflection-Fourier transform infrared spectroscopy (ATR-FT-IR). The covalent bond between APTES-functionalized SiO₂ nanoparticles (nSiO₂-APTES), and the hydrolyzed polyacrylamide (HPAM) chain (MW ≈ 20.10⁶ Da) was confirmed with high-resolution X-ray spectroscopy (XPS). Finally, the thermal properties of the nanohybrid were evaluated by using thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). The results showed that the CSNH-PC1 has a spherical morphology, with sizes between 420–480 nm and higher thermal resistance compared to HPAM polymers without modification, with a glass transition temperature of 360 °C. The integration of these advanced characterization techniques implemented here shows promising results for the study and evaluation of new nanomaterials with multiple applications.

In this work, we studied the methylene blue (MB) dye adsorption capacity on biochar derived from residues of Prosopis juliflora seed waste, a species found in the region of the tropical dry forest of Piojó in the Department of Atlántico, Colombia. The materials were obtained by pyrolysis at temperatures of 300, 500, and 700 °C. Biochar was characterized using Fourier transform infrared (FTIR), scanning electron microscopy and energy-dispersive X-ray spectroscopy (SEM-EDX), TGA, and Brunauer-Emmett-Teller (BET) techniques. The three biochar samples presented a macroporous, rough structure with pore size between 6 and 28 μm. The largest pore surface area observed was 1.28 m²/g for pyrolyzed biochar produced at 500 °C, larger than that of biochar produced at 700 °C, which was 0.83 m²/g. The adsorption results show that the maximum percentage of MB removal was 69%. According to SEM results, the material's pore sizes varied on average from 6 to 28 μm. We modeled MB adsorption on biomass through three different isotherm models. The Freundlich model was the best-fitting model for the removal of MB (K _F = 1.447; 1/n = 0.352). The kinetic results showed that the pseudo-second-order model was the best-fitting model for the sorption process (q _e = 2.94 mg/g; k ₂ = 0.087 g/(mg/min^-1)). Furthermore, the recycling test showed that the biochar did not change its adsorption capacity significantly. Finally, under the experimental conditions, the thermodynamic parameters indicated that the removal of MB using biochar was an endothermic and spontaneous process; all ΔG° values ranged from -2.14 to -0.95 kJ/mol; ΔH° was 23.54 kJ/mol and ΔS° was 79.5 J/mol.