We thoroughly explored the physical origin of the efficiency decrease with increasing injection current and current crowding effect in 280 nm AlGaN-based flip-chip deep-ultraviolet (DUV) light-emitting diodes (LEDs). The current spreading length was experimentally determined to be much smaller in DUV LEDs than that in conventional InGaN-based visible LEDs. The severe self-heating caused by the low power conversion efficiency of DUV LEDs should be mainly responsible for the considerable decrease of efficiency when current crowding is present. The wall-plug efficiency of the DUV LEDs was markedly enhanced by using a well-designed p -electrode pattern to improve the current distribution.
Because of its large bandgap of ∼6.0 eV and suitability for high p-type doping, hexagonal boron nitride (h-BN) has become a candidate material that can serve as a p-layer by forming a heterostructure with AlGaN materials with a high Al fraction in deep-ultraviolet optoelectronic devices. The band offsets at the heterojunction are crucial to the device design because they determine the hole and electron transport properties across the heterojunction. In this study, we give the band alignment between h-BN and Al0.7Ga0.3N using the valence and conduction band offsets. The valence band offset of the h-BN/Al0.7Ga0.3N heterojunction is determined via X-ray photoelectron spectroscopy (XPS) to be as small as −0.01 ± 0.09 eV. The small valence band discontinuity that occurs at the h-BN/Al0.7Ga0.3N interface is further confirmed using angle-resolved valence band spectra from the XPS measurements. By combining the bandgap values of Al0.7Ga0.3N and h-BN which were estimated using absorption spectra measurements, the conduction band offset is found to be approximately 0.89 ± 0.09 eV. These results indicate that h-BN is an excellent material for hole injection into Al0.7Ga0.3N. Meanwhile, the electrons can be effectively blocked away from h-BN. These results will be helpful in the design of group-III-nitride-based optoelectronic devices, particularly deep-ultraviolet light-emitting diodes and lasers.
9 October 2020 in Journal of Physics D: Applied Physics
The external quantum efficiency (EQE) in electrically injected AlGaN-based deep-ultraviolet light-emitting diodes (DUV-LEDs) is severely limited by their poor current injection efficiency (CIE). We report improvement in the CIE via controlling the relaxation of strains in the p-AlGaN hole injection layer (HIL) and the electron blocking layer (EBL). Simulation results show that an unrelaxed strain in the HIL associated with a relaxed strain in EBL can significantly enhance CIE. Deeper analysis indicates that high hole concentrations can be generated at HIL/EBL interface by strain-induced piezoelectric fields, which can then provide abundant numbers of holes for injection into quantum wells. Two sub-280 nm DUV-LEDs were fabricated with specific designs for different strain relaxations in the p-AlGaN HIL by changing the HIL thickness from 200 to 20 nm. The strain difference was identified using Raman spectroscopy. Electroluminescence measurements demonstrated much higher EQE in the strained-HIL DUV-LEDs. By separating the EQE contributions of three efficiencies, i.e. the CIE, the radiative recombination efficiency and the light extraction efficiency, we found that the EQE enhancement could mainly be attributed to the improved CIE, which agreed well with the simulation results.
Hexagonal boron nitride (h-BN) is an attractive wide-bandgap material for application to emitters and detectors operating in the deep ultraviolet (DUV) spectral region. The optical transmittance of h-BN in the DUV region is particularly important for these devices. We report on the deposition of thick h-BN films (>200 nm) on Al0.7Ga0.3N templates via radio-frequency sputtering, along with the realization of ultrahigh transmittance in the DUV region. The fraction of the gas mixture (Ar/N2) was varied to investigate its effects on the optical transmittance of BN. DUV light transmittance of as high as 94% was achieved at 265 nm. This value could be further enhanced to exceed 98% by a post-annealing treatment at 800 °C in a N2 ambient for 20 min. The phase of the highly DUV–transparent BN film was determined to be a purely hexagonal structure via Raman spectra measurements. More importantly, these deposition processes were performed at a low temperature (300 °C), which can provide protection from device performance degradation when applied to actual devices.
We report an enhancement of the wall-plug efficiency (WPE) of AlGaN-based deep-ultraviolet light-emitting diodes (DUV-LEDs). This enhancement was achieved through fabrication of a micro-mesh p-electrode (p-GaN/metals) and scattering nanostructures on the p-side of the device to obtain both high electrical efficiency and enhanced light extraction efficiency (LEE). The micro-mesh p-electrode structure minimizes DUV light absorption by removing a part of the p-GaN layer while maintaining good electrical conduction. The scattering nanostructures, which consist of truncated HfO2 cones, redirect guided light effectively into the escape cone, thus improving the LEE significantly. As a result, the WPE reached 9.1% at an injection current of 12 mA and an emission wavelength of 275 nm. This efficiency was enhanced by approximately 1.7 times when compared with that of conventional DUV-LEDs, in which a p-electrode structure covers the entire mesa. Although the micro-mesh p-electrode was used to reduce DUV light absorption, high electrical efficiency of 90% was demonstrated, with a drive voltage of as low as 4.8 V at 12 mA. These experimental results show good agreement with the results of three-dimensional finite-difference time-domain simulations.
Sub-wavelength-sized ridge structures that satisfy evanescent wave coupling effect requirements at the emission wavelength were fabricated through the photolithography and wet chemical etching of the light-extraction surface of a thin-film type AlGaInP light-emitting diode (LED). By doing this, the light output power relative to a reference LED with a flat light-extraction surface was increased by a factor of approximately 3.8, corresponding to an equivalent enhancement in light-extraction efficiency that is possibly attributable to an evanescent wave coupling effect occurring on the surfaces of the minute ridge structures.