An acoustic sea glider has been developed for ambient sea noise measurement and target detection through the deployment of an acoustic vector sensor (AVS). The glider was designed with three cabins connected in sequence and it can dive to depths exceeding 1200m. The AVS fixed on the glider measure acoustic pressure and particle velocities related to undersea noise, and the inner attitude sensors can effectively eliminate the estimation deviation of the direction of arrival. The inherent self-noises of the acoustic sea glider and AVS are presented respectively in respect to the Knudsen spectra of sea noise. Sea trial results indicate that the AVS could work well for undersea noise measurement when the glider is smooth sliding, and the target azimuth estimated by AVS after correction is remarkably consistent with the values measured by the GPS, and direction-finding errors are less than 10 degrees. The research in this paper shows that the acoustic sea glider is able to undertake tasks such as a wide range of underwater acoustic measurement and detection.
Traditionally, matrix-based methods for reverberation reduction have prioritized a high signal-to-reverberation ratio over low time consumption. This letter describes a fast reverberation-reduction algorithm. The reverberation-reduction problem is formulated as an inexact matrix decomposition. A low-rank matrix is obtained through the reverberation extraction in a low-dimensional matrix, and a two-stage structure optimizes the computation iterative frame. The proposed algorithm's convergence, time consumption, and error are numerically simulated. Field data processing results demonstrate that the algorithm achieves a similar receiver operating characteristic (ROC) curve as with the alternating direction multiplier method (ADMM) but reduces the time consumption by 33%.
The vibration caused by the movement of internal actuating components within an acoustic underwater glider can interfere with onboard sensors. However, as a new vibration-damping material, phononic crystals can effectively reduce this impact. Using simulation and an underwater test, this work studied the vibration-damping mechanism of the phononic crystal suspension (PCS) designed by Tianjin University, China. The bandgaps and the modes of PCS were calculated first, which offered basic data for the following simulation. Then, the relationship between the modes and attenuation zones (AZs) were broadly considered to reveal the variation law of the AZs with the change in modes, both in the air and under water. Finally, an underwater test was carried out to verify the good vibration-damping effect of the PCS. The results show that the cutoff frequency of the AZs could be predicted by finding the relevant modes. The PCS showed a good vibration-damping effect from 170 Hz to 5000 Hz in the underwater test, with a maximum decrease of 6 dB at 2000 Hz. Finally, the damping of the PCS could suppress the overlap of modes that resulted from Bragg scattering. This work will also provide theoretical guidance for further study on the optimization of phononic crystal mechanisms for vibration damping.
To meet the critical need for compact, multifunctional acoustic vector sensors on deep-sea unmanned platforms such as acoustic profiling buoys and underwater gliders, we have developed a novel composite resonant acoustic vector sensor capable of large-depth operations. The sensor innovatively integrates the sound pressure channel and the vector channel, and utilizes the conjugate cross-spectrum between them to effectively reduce the isotropic noise, enhance the detection of weak signals from ships, and make up for the shortcomings of a single sound pressure channel and a vector channel. Certified to function reliably at depths up to 1500 m, field sea trials confirm its efficacy in deep-sea deployments, capturing essential marine environmental noise data. Key analysis during sea trials focused on marine ambient noise levels captured at frequencies of 65 Hz, 125 Hz, 315 Hz, 400 Hz, and 500 Hz, correlating these with changes in depth. The test results revealed the following insights: (a) At the same depth, the marine environmental noise level increases as the frequency decreases; (b) At the same frequency, the marine environmental noise level decreases with increasing depth; (c) Under favorable deep-sea conditions, the marine environmental noise level reaches 55 decibels (dB) at 500 Hz; (d) Noise levels tend to increase at various frequencies when surface ships are in proximity. These findings underscore its significant potential for enhancing deep-sea acoustic surveillance and exploration.
To address the trade-off between acoustic stealth and hydrodynamic efficiency in underwater glider design, this study proposes a coupled multi-physics parametric design framework for acoustic matching structures. Using the “Dolphin” glider as a case, geometric effects on acoustic scattering were analyzed by comparing spherical, capsule, and ellipsoidal structures under acoustic incidence. The ellipsoid configuration showed a superior performance and was further optimized through parameterized Myring profiles with length-to-diameter ratios (1.8–1.875) and sharpness factors (n = 1–5). Integrated CFD-BEM simulations revealed that the optimal design (ratio 1.875, n = 2) reduces the scattering sound pressure level by 1.8 dB at 1 kHz and drag coefficient by 14.2%. At 3 m/s, bow-direction target strength decreased by 6 dB, with 4.4 dB flow noise reduction. This methodology effectively resolves acoustic–fluid conflicts, advancing low-noise underwater vehicle design.