Polylactic acid (PLA) is expected to replace many general-purpose plastics, especially those used for food packaging and agricultural mulch. In composting, the degradation speed of PLA is affected by the molecular weight, crystallinity, and microbial activity. PLA with a molecular weight of less than 10,000 has been reported to have higher decomposition rates than those with higher molecular weight. However, PLA degradation generates water-soluble products, including lactic acid, that decrease the pH of soil or compost. As acidification of soil or compost affects farm products, their pH should be controlled. Therefore, a method for determining suitable reaction conditions to achieve ideal decomposition products is necessary. This study aimed to determine suitable reaction conditions for generating preprocessed PLA with a molecular weight lower than 10,000 without producing water-soluble contents. To this end, we investigated the degradation of PLA using sub-critical water. The molecular weight and ratio of water-soluble contents (WSCs) affecting the pH of preprocessed products were evaluated through kinetic analysis, and crystallinity was analyzed through differential scanning calorimetry. Preprocessed PLA was prepared under the determined ideal conditions, and its characteristics in soil were observed. The results showed that the crystallization rate increased with PLA decomposition but remained lower than 30%. In addition, the pH of compost mixed with 40% of preprocessed PLA could be controlled within pH 5.4–5.5 over 90 days. Overall, soil mixed with the preprocessed PLA prepared under the determined ideal conditions remains suitable for plant growth.
The performance of CO2-expanded hexane in the vapor-liquid two-phase region was examined to extract phosphorus-free bio-oil from rice bran. Previously, it was found that in the uniform liquid phase region, it is difficult to maintain the phosphorus concentration at a stable and low level when the CO2 mole fraction changed slightly. To overcome this issue, the dependences of the phosphorus and free fatty acid concentrations, the oil solubility, and the oil yield on the CO2 mole fraction in the CO2-expanded hexane were measured at 25 °C, 5.1–5.2 MPa, and at a CO2 mole fraction of 0.88–0.94 in the two-phase region. Thus, a relatively constant phosphorus concentration of <10 ppm was maintained in the extracted oil, which was ~1/50 of that in the oil extracted by hexane, thereby satisfying the European unified standard for biodiesel fuel. Furthermore, a high oil yield exceeding that of hexane extraction was maintained over all CO2 mole fractions. Moreover, the oil solubility in the CO2-expanded hexane decreased linearly with the CO2 mole fraction, and so this factor represented the oil-dissolving power of the extractant more accurately than the oil yield used previously. The free fatty acid concentration was 83% of that extracted by hexane.
Efficient, low-cost methods are required to produce impurity-free bio-oils with minimal nutrient depletion. This study investigated the effect of extraction and pretreatment conditions on the quality of rice bran oil extracted with CO2-expanded hexane. The extraction conditions considered were temperature (20–30 °C), CO2 mole fraction (0.76–0.94), and pressure (4.2–7.0 MPa). The effectiveness of rice bran hot air drying at 80–100 °C for 0.5, 1, 3, and 5 h for lipase inactivation was also studied. The rice bran oil yield and the content of free fatty acids did not depend significantly on the extraction temperature or pressure. The oil solubility increased significantly (p < 0.05) with every 5 °C increment while decreasing significantly at pressures below 5.0 MPa. The optimum extraction conditions for phosphorus-free rice bran oil (phosphorus concentrations of 9.8, 9.1, and 6.2 ppm) were CO2 mole fraction of 0.82 at 5.1 MPa and 20 °C, CO2 mole fraction of 0.87 at 5.0 MPa and 25 °C, and CO2 mole fraction of 0.92 at 5.1 MPa and 30 °C, respectively. The most effective pretreatment conditions for rice bran before storage for 10 weeks were 100 °C for 1 h. In addition, the phosphorus concentration of rice bran oil extracted with CO2-expanded hexane at a CO2 mole fraction of 0.88, 5.1 MPa, and 25 °C was ≤ 7.00 ppm, regardless of the pretreatment conditions. Therefore, CO2-expanded hexane extraction can be potentially used to produce impurity-free rice bran oil from both treated and untreated rice bran without refining.
An environmentally friendly and efficient polymer coating method for micro-sized particles was developed using supercritical CO2. Because this method used supercritical CO2 as the solvent to dissolve the coating material, we avoided environmental pollution from organic solvents, saved the energy required to evaporate/remove organic solvents, realized a uniform coating film on the fine particles, and prevented agglomeration of the coating particles. The solubilities of the five silicone resins used as coating materials were measured using the flow method, and the data were well correlated by Chrastil’s equation with an average deviation of 5.7%. Resins comprising numerous methyl-group side chains exhibited high solubilities and were suitable coating materials. A new semi-flow-type coating method using supercritical CO2 was also developed, which deposited a film with a uniform thickness of 0.2–1.3 μm on whole fine particles. Notably, in this method, the film thickness was easily controlled. A simple and rapid technique was developed for measuring the coating thickness using X-ray fluorescence analysis. The model for calculating the coating film thickness was based on the material balance of the coating material. This model satisfactorily predicted the thickness with an average error of 0.085 μm by measuring the solubility of the coating material in supercritical CO2, integrated flow volume of supercritical CO2, particle diameter, density and charged weight of the fine particle, and coating material density.
16 December 2025 in Food and Bioprocess Technology
The discovery that waste rice bran contains ~ 3% γ-oryzanol has led to growing investigations into its extraction and evaluation using green technologies. This study aimed to investigate the potential application of CO2-expanded liquids (CXLs) in the extraction of γ-oryzanol-rich rice bran oil. The effects of the extraction solvents were studied, and thereafter, the effects of the extraction temperature (20–30 °C) and rice bran particle size were analyzed using the optimal solvent. The rice bran oil yields of 0.24 ± 0.01 g/g-sample were achieved through CXL extraction. Besides, the γ-oryzanol yields were 13.06 ± 0.73–23.68 ± 1.30 mg/g-sample, resulting in 93.24 ± 1.25 mg/g-oil of γ-oryzanol content. More specifically, CO2-expanded acetone (CXA) and CO2-expanded ethanol (CXE) offered the highest γ-oryzanol yields (i.e., 19.19 ± 0.33 mg/g-sample) compared to 11.07 ± 0.13 mg/g-sample for CO2-expanded hexane (CXH). The γ-oryzanol yield was increased to 23.16 ± 0.26 mg/g-sample by increasing the extraction time and temperature and also by reducing the particle size of the waste rice bran. Moreover, CXA and CXH offered the highest oil qualities, with phosphorus concentrations of 2.9 and 3.0 ppm, respectively. Furthermore, the obtained rice bran oil contained 1.45 ± 0.04–6.65 ± 0.08 mg-GAE/g-oil of total phenolic compounds, along with a DPPH scavenging activity of ≤ 89 ± 1.40%. The findings show that not only high yield and quality rice bran oil can be achieved but also nutrient retention. Therefore, CXLs are suitable extractants for γ-oryzanol-rich rice bran oil. Graphical Abstract