Prabir Daripa

Prof. Prabir Daripa

Department of Mathematics, Texas A&M University at College Station, TX, USA

Research Focus & Metrics

Academic Career Length

35Years (1992-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 April 2017 in Journal of Computational Physics
Verified
Journal Article
Closed access
Prabir DaripaPrabir Daripa
Prabir Daripa
SDSourav Dutta
Sourav Dutta

31 January 2003 in International Journal of Engineering Science
Verified
Journal Article
Closed access
Prabir DaripaPrabir Daripa
Prabir Daripa
RDRanjan K. Dash
Ranjan K. Dash

1 January 2015 in Physics of Fluids
Verified
Journal Article
Closed access
PDF file
CGCraig Gin
Craig Gin
Prabir DaripaPrabir Daripa
Prabir Daripa
Motivated by stability problems arising in the context of chemical enhanced oil recovery, we perform linear stability analysis of Hele-Shaw and porous media flows in radial geometry involving an arbitrary number of immiscible fluids. Key stability results obtained and their relevance to the stabilization of fingering instability are discussed. Some of the key results, among many others, are (i) absolute upper bounds on the growth rate in terms of the problem data; (ii) validation of these upper bound results against exact computation for the case of three-layer flows; (iii) stability enhancing injection policies; (iv) asymptotic limits that reduce these radial flow results to similar results for rectilinear flows; and (v) the stabilizing effect of curvature of the interfaces. Multi-layer radial flows have been found to have the following additional distinguishing features in comparison to rectilinear flows: (i) very long waves, some of which can be physically meaningful, are stable; and (ii) eigenvalues can be complex for some waves depending on the problem data, implying that the dispersion curves for one or more waves can contact each other. Similar to the rectilinear case, these results can be useful in providing insight into the interfacial instability transfer mechanism as the problem data are varied. Moreover, these can be useful in devising smart injection policies as well as controlling the complexity of the long-term dynamics when drops of various immiscible fluids intersperse among each other. As an application of the upper bound results, we provide stabilization criteria and design an almost stable multi-layer system by adding many layers of fluid with small positive jumps in viscosity in the direction of the basic flow.

1 February 2002 in Applied Mathematics and Computation
Verified
Journal Article
Closed access
RDRanjan K. Dash
Ranjan K. Dash
Prabir DaripaPrabir Daripa
Prabir Daripa

5 March 2021 in Physical Review Fluids
Verified
Journal Article
Closed access
PDF file
CGCraig Gin
Craig Gin
Prabir DaripaPrabir Daripa
Prabir Daripa
We use linear stability analysis to demonstrate how to stabilize multilayer radial Hele-Shaw and porous media flows with a time-dependent injection rate. Sufficient conditions for an injection rate that maintains a stable flow are analytically derived for flows with an arbitrary number of fluid layers. We show numerically that the maximum injection rate for a stable flow decreases proportional to t−1/3 for t≫1 regardless of the number of fluid layers. However, the constant of proportionality depends on the number of layers and increases at a rate that is proportional to the number of interfaces to the two-thirds power. Therefore, flows with more fluid layers can be stable with faster time-dependent injection rates than comparable flows with fewer fluid layers, even when the additional layers are very thin. We also show that for unstable flows, which may be required to inject a given amount of fluid in a fixed amount of time, an increasing injection rate is less unstable than a constant or decreasing injection rate, and that the inclusion of more fluid layers can overcome poor injection strategies.

1 April 2023 in Physics of Fluids
Verified
Journal Article
Closed access
PDF file
Prabir DaripaPrabir Daripa
Prabir Daripa
RMRohit Mishra
Rohit Mishra
Two distinct effects that polymers exhibit are shear thinning and viscoelasticity. The shear thinning effect is important as the polymers used in chemical enhanced oil recovery usually have this property. We propose a novel approach to incorporate shear thinning effect through effective dynamic viscosity of the shear thinning polysolution. The procedure of viscosity calculation of the polysolution, although based on a very basic power law model, is based on empirical coefficients that depend on a spatio-temporally evolving variable, namely, concentration of polymer. Since viscosity calculation is performed in space and time, the results obey correct physics and are more accurate than what exists in the literature. This method has been integrated with an existing method for a Newtonian physics based model of porous media flows. The solver uses a hybrid numerical method developed by Daripa and Dutta [“DFEM-MMOC based EOR code in MATLAB” (2020); P. Daripa and S. Dutta, “Modeling and simulation of surfactant–polymer flooding using a new hybrid method,” J. Comput. Phys. 335, 249–282 (2017); and P. Daripa and S. Dutta, “On the convergence analysis of a hybrid numerical method for multicomponent transport in porous media,” Appl. Numer. Math. 146, 199–220 (2019)]. The above method solves a system of coupled elliptic and transport equations modeling Darcy's law based polymer flooding process using a discontinuous finite element method and a modified method of characteristics. Simulations show (i) competing effects of shear thinning and mobility ratio; (ii) injection conditions, such as injection rate and injected polymer concentration, influence the choice of polymers to optimize cumulative oil recovery; (iii) permeability affects the choice of polymer; (iv) dynamically evolving traveling viscosity waves; and (v) shallow mixing regions of small scale viscous fingers in homogeneous porous media. The overall goal of this study is to develop an effective yet easy approach to make design choices of polymers in any given flooding condition, which has been shown here.