Direct seafloor sampling using, e.g., box corers is insufficient to obtain an acceptable accuracy of nodule resource estimates in small parts of potential deposits. In order to increase the reliability of the estimates, it was rational to use the results of photographic surveys of the seafloor. However, the estimation of nodule abundance based on seafloor photographs is associated with a number of problems and limitations. The main goal of the study was a statistical analysis of the role and interrelationships of selected factors affecting the accuracy of nodule abundance assessment based on seafloor photographs from the H22 exploration block located in the Interoceanmetal Joint Organization (IOM) area in the Pacific. A statistically significant, but only moderately strong, correlation was found between the abundance of nodules and seafloor nodule coverage (quantitative variables), the nodule abundance and genetic type of nodules (ordinal variable estimated visually from photos), and between seafloor coverage with nodules and sediment coverage of nodules (ordinal variable estimated visually from photos). It was suggested that the nodule abundance could be effectively and more accurately predicted using a general linear model that includes both quantitative and ordinal variables.
The amount and accuracy of nodule resources estimation in the Pacific Ocean are among the main factors conditioning the future exploitation. The estimates are based on the results of classical, direct seafloor sampling. Due to the large distance between sampling sites, the accuracy of assessing nodule resources in small parts of the deposit is low. The accuracy can be increased by using a large number of seafloor photographs taken along the route of the research vessel performing classic sampling. The study conducted for a part of the area administered by Interoceanmetal Joint Organization (IOM) included: (i) determining a model of the relationship between nodule abundance and seafloor nodule coverage using statistical methods, (ii) assessing the accuracy of nodule resources estimation using a geostatistical kriging procedure, (iii) proposing a preliminary classification of resources referring to International Seabed Authority (ISA) classification standards as material for further discussion. It was found that achievement of high accuracy in the estimation of nodule resources (with relative standard error <5%) in blocks planned for annual exploitation based on direct sampling is difficult. While the use of seafloor photographs increases the accuracy of estimating nodule resources, this improvement is not radical due to the unfavorable, preferential arrangement of photographic data.
The success of the future exploitation of the Pacific polymetallic nodule deposits depends on an accurate estimation of their resources, especially in small batches, scheduled for extraction in the short term. The estimation based only on the results of direct seafloor sampling using box corers is burdened with a large error due to the long sampling interval and high variability of the nodule abundance. Therefore, estimations should take into account the results of bottom photograph analyses performed systematically and in large numbers along the course of a research vessel. For photographs taken at the direct sampling sites, the relationship linking the nodule abundance with the independent variables (the percentage of seafloor nodule coverage, the genetic types of nodules in the context of their fraction distribution, and the degree of sediment coverage of nodules) was determined using the general linear model (GLM). Compared to the estimates obtained with a simple linear model linking this parameter only with the seafloor nodule coverage, a significant decrease in the standard prediction error, from 4.2 to 2.5 kg/m2, was found. The use of the GLM for the assessment of nodule abundance in individual sites covered by bottom photographs, outside of direct sampling sites, should contribute to a significant increase in the accuracy of the estimation of nodule resources.
1 January 2012 in Gospodarka Surowcami Mineralnymi - Mineral Resources Management
The most important reasons for the limited credibility of 3D geochemical models of the Cu-Ag deposits (The Lubin-Głogów Copper District) are unfavorable statistical characteristics of the main metals (Cu, Ag), and the unfavorable structure of their variability with a relatively poorly marked non-random component of variability. It is hoped that the accuracy of geochemical models can be increased by previous lithological modeling of a given deposit. This is due to significant differences in mean Cu content in both the main lithological series (carbonates, shales and sandstones) and individual lithological units within them, which justifies separate geochemical modeling of each. The paper presents the results of the comparison of the reliability of 3D modeling of Cu content carried out in both individual and main lithological units of the Cu-Ag Rudna deposit (The Lubin- Głogów Copper District). The 3D lithological models were made using ordinary kriging (main lithological units) and Plurigaussian simulation (individual lithological units). The 3D estimation of Cu content within lithological models was carried out using the ordinary kriging (OK ) and squared inverse distance (ID2) methods. The verification of the accuracy of Cu estimates in the 3D model using spot samples of the test data set has shown only a slight increase in the accuracy of the estimates of Cu content within the individual lithological units of the shale series compared to the estimates of Cu content in the whole main lithology. In most cases, 3D models of Cu content carried out using the ordinary kriging method are slightly more accurate than the analogous squared inverse distance weighting method.
20 November 2018 in Biuletyn Państwowego Instytutu Geologicznego
The article discusses the lithological and facies development of the copper ore deposit in the Fore-Sudetic Monocline in the so-called depression at the top of the Weissliegend. The lithological variability and quality parameters of the deposit in the exploitation field located between the Central and Northern elevations of Rudna, where the deposit profile is described as “typical”, i.e. the Cu-Ag mineralization occurs in all three basic lithological types of copper ore, is analyzed. The lithological variability of ores in depression zones is the reason why the degree of mineralization and the parameters of the economic deposit are highly variable. The authors focused on the mutual relationships between the neighbouring lithological units and the development of the balance deposit. To illustrate the variability of deposit parameters closely related to the lithological and facies development of the host rocks, three-dimensional lithological and geochemical models and isoline maps of the thickness of individual specific copper ore types were made using geostatistical methods and based on field observations and sampling of the deposit.