High‐pressure and high‐temperature phase relations in the system Mg2SiO4‐Fe2SiO4 were thoroughly reinvestigated at pressures up to 21 GPa and at temperatures of 1200°C and 1600°C using a uniaxial split‐sphere apparatus. Both normal and reverse experiments were performed on the univariant reactions. Both exsolving and dissolving experiments were performed to determine the divariant loops at 1600°C. The run products were examined using microfocused X ray diffractometry, scanning electron microscopy, and electron probe microanalysis. The phase diagrams thus constructed were compared with those previously proposed using an experimental or thermochemical method. Phase changes in mantle olivine with Mg number of 89 occur in the following order: (α) − (α+β) − (β) − (β+γ) − (γ). The α+β loop narrows with increasing temperature. The applicability of an isochemical peridotitic mantle model is discussed in the light of the location and thickness of the 400‐km discontinuity.
1 November 2010 in Physics of the Earth and Planetary Interiors
Eulerian finite strain of an elastically isotropic body is defined using the expansion of squared length and the post-compression state as reference. The key to deriving second-, third- and fourth-order Birch–Murnaghan equations-of-state (EOSs) is not requiring a differential to describe the dimensions of a body owing to isotropic, uniform, and finite change in length and, therefore, volume. Truncation of higher orders of finite strain to express the Helmholtz free energy is not equal to ignoring higher-order pressure derivatives of the bulk modulus as zero. To better understand the Eulerian scheme, finite strain is defined by taking the pre-compressed state as the reference and EOSs are derived in both the Lagrangian and Eulerian schemes. In the Lagrangian scheme, pressure increases less significantly upon compression than the Eulerian scheme. Different Eulerian strains are defined by expansion of linear and cubed length and the first- and third-power Eulerian EOSs are derived in these schemes. Fitting analysis of pressure-scale-free data using these equations indicates that the Lagrangian scheme is inappropriate to describe P-V-T relations of MgO, whereas three Eulerian EOSs including the Birch–Murnaghan EOS have equivalent significance.
25 February 2004 in Journal of Geophysical Research
Phase relations of the olivine‐wadsleyite transition in the system (Mg,Fe)2SiO4 have been determined at 1600 and 1900 K using the quench method in a Kawai‐type high‐pressure apparatus. Pressure was determined at a precision better than 0.2 GPa using in situ X‐ray diffraction with MgO as a pressure standard. The transition pressures of the end‐member Mg2SiO4 are estimated to be 14.2 and 15.4 GPa at 1600 and 1900 K, respectively. Partition coefficients for Fe and Mg between olivine and wadsleyite are 0.51 at 1600 K and 0.61 at 1900 K. By comparing the depth of the discontinuity with the transition pressure, the temperature at 410 km depth is estimated to be 1760 ± 45 K for a pyrolitic upper mantle. The mantle potential temperature is estimated to be in the range 1550–1650 K. The temperature at the bottom of the upper mantle is estimated to be 1880 ± 50 K. The thickness of the olivine‐wadsleyite transition in a pyrolitic mantle is determined to be between 7 and 13 km for a pyrolitic mantle, depending on the efficiency of vertical heat transfer. Regions of rapid vertical flow (e.g., convection limbs), in which thermal diffusion is negligible, should have a larger transition interval than stagnant regions, where thermal diffusion is effective. This is in apparent contradiction to short‐period seismic wave observations that indicate a maximum thickness of <5 km. An upper mantle in the region of the 410 km discontinuity with about 40% olivine and an Mg# of at least 89 can possibly explain both the transition thickness and velocity perturbation at the 410 km discontinuity.