Rengui Weng

Dr. Rengui Weng


Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
8 January 2020 in RSC Advances
Verified
Journal Article
Open access
PDF file
RWRengui Weng
Rengui Weng
XHXin Huang
Xin Huang
DLDongqi Liao
Dongqi Liao
SXSheng Xu
Sheng Xu
LPLei Peng
Lei Peng
XLXinzhong Liu
Xinzhong Liu
Bamboo cellulose (BC) is one of the most abundant renewable, hydrophilic, inexpensive, and biodegradable organic materials. The cellulose membrane is one of the best materials for replacing petroleum-based polymer films used for water purification. In this study, N-methylmorpholine-N-oxide (NMMO) was used as a solvent to dissolve cellulose and chitosan, and a regenerated cellulose/chitosan membrane (BC/CSM) was prepared by phase inversion. A new kind of cellulose/chitosan nanofiltration membrane (IP-BC/CS-NFM) was obtained by the interfacial polymerization of piperazine (PIP) and trimesoyl chloride (TMC). The IP-BC/CS-NFM was characterized by Fourier transform infrared spectroscopy (FT-IR), field emission scanning electron microscopy (FE-SEM), atomic force microscopy (AFM), thermal gravimetric analysis (TGA), the retention rate, and water flux. FT-IR analysis showed that polypiperazine amide was formed. Additionally, FE-SEM and AFM showed that a uniform roughness and dense functional layer was formed on the surface of the IP-BC/CS-NFM. Furthermore, TGA analysis showed that the thermal stability of IP-BC/CS-NFM is better than that of BC/CSM. The inorganic salt retention of IP-BC/CS-NFM was measured using a membrane performance evaluation instrument, following the order R(Na2SO4) > R(MgSO4) > R(MgCl2) > R(NaCl). At a pressure of 0.5 MPa, the retention rates for NaCl, Na2SO4, MgSO4, MgCl2, Methyl Orange, and Methyl Blue were 40.26%, 71.34%, 62.55%, 53.28%, 93.65%, and 98.86%, and the water flux values were 15.64, 13.56, 14.03, 14.88, 13.28, and 12.35 L m−2 h−1, respectively. The IP-BC/CS-NFM showed better water flux and a higher rejection rate in aqueous dye-salt solutions, and had a good separation performance under different operating pressure conditions.

23 March 2017 in Polymers
Verified
Journal Article
Open access
PDF file
RWRengui Weng
Rengui Weng
LCLihui Chen
Lihui Chen
SLShan Lin
Shan Lin
HZHui Zhang
Hui Zhang
HWHui Wu
Hui Wu
LHLiulian Huang
Liulian Huang
Presently, most nanofiltration membranes are prepared with non-biodegradable petrochemical materials. This process is harmful to the ecosystem and consumes a large amount of non-renewable energy. In this study, biodegradable and biocompatible antibacterial cellulose/chitosan nanofiltration membranes (BC/CS-NFMs) were fabricated and characterized for their mechanical strength, antimicrobial activity, salt and dye filtration performance, and polyethylene glycol (PEG) retention using Thermal gravimetric analysis (TGA), Field emission scanning electron microscopy(FE-SEM), Fourier transform infrared spectroscopy(FT-IR), and X-ray diffraction (XRD). The BC/CS-NFMs were obtained by the hydrolysis and carboxymethylation of dense cellulose/chitosan membranes (BC/CSMs). The tensile strength of the BC/CS-NFMs decreased as the chitosan content increased. In addition, the thermal stability and antibacterial ability of the BC/CS-NFMs improved. The pore size is less than 1 nm, and a spongy, layered structure is observed in the cross-sectional FE-SEM images. FT-IR analysis shows that a part of the hydroxyl in cellulose transforms to carboxymethyl during the hydrolysis and carboxymethylation of the BC/CSMs. No obvious changes can be observed in the cellulose and chitosan after the blend membrane formation from the XRD measurements. Based on the experimental results on the permeation and rejection of BC/CS-NFMs, different proportions of cellulose and chitosan nanofiltration membranes almost did not affect the water flux and rejection rate. The BC/CS-NFMs showed better water flux and a higher rejection rate in aqueous dye-salt solutions.

22 April 2020 in Green Chemistry
Verified
Journal Article
Closed access
PDF file
RWRengui Weng
Rengui Weng
ZYZhihao Yu
Zhihao Yu
JXJian Xiong
Jian Xiong
Xuebin LuXuebin Lu
Xuebin Lu
A critical review on the effects of water solvent that contribute to the sustainable development of biomass-derived levulinic acid valorization systems.

1 December 2021 in Chemosphere
Verified
Journal Article
Closed access
RWRengui Weng
Rengui Weng
FTFeng Tian
Feng Tian
ZYZhendong Yu
Zhendong Yu
JMJiachen Ma
Jiachen Ma
YLYuancai Lv
Yuancai Lv
RWRengui Weng
Rengui Weng

19 October 2021 in Catalysis Science & Technology
Verified
Journal Article
Closed access
PDF file
RWRengui Weng
Rengui Weng
Xuebin LuXuebin Lu
Xuebin Lu
NJNa Ji
Na Ji
AFAtsushi Fukuoka
Atsushi Fukuoka
ASAbhijit Shrotri
Abhijit Shrotri
ZYZhihao Yu
Zhihao Yu
This minireview highlights versatile routes for catalyst nanostructure modulation for better hydrogenation selectivity control of typical biomass-derived furan platform chemicals to tame the butterfly effect on the catalytic selectivity.

1 March 2020 in Energies
Verified
Journal Article
Open access
PDF file
YFYaming Fan
Yaming Fan
XLXiangdong Li
Xiangdong Li
MZMinfeng Zheng
Minfeng Zheng
RWRengui Weng
Rengui Weng
JTJiyuan Tu
Jiyuan Tu
The exhaust/return-split configuration is regarded as an important upgrade of traditional under-floor-air-distribution (UFAD) systems due to its higher energy efficiency. Moreover, existing studies are mostly focused on the effect of the return vent height on the performance of an UFAD system under cooling conditions. Knowledge of the performance under heating conditions is sorely lacking. This paper presents a numerical evaluation of the performance characteristics of an UFAD system with six different heights of the return vents in heating operation by comprehensively considering thermal comfort, air quality, and energy consumption. The results show that, in the heating mode, the general thermal comfort (predicted mean vote-predicted percentage dissatisfied (PMV-PPD) values) and indoor air quality indices (mean age of air and volatile organic compounds (VOCs) concentration) were greatly improved and energy consumption was slightly reduced with a lower return vent height. Although these were opposite to the findings of our previous study regarding the performance in cooling mode, an optimal return vent height in terms of the comprehensive all-year performance can be recommended. This method provides insight into the design and optimization of the return vent height of UFAD for space heating and cooling.