Growth of LiTaO3 film on a type-p silicon substrate (100) was conducted using the Chemical Solution Deposition (CSD) and spin coating methods at a speed of 3000 rpm for 30 seconds. The film on the substrate was then heated at 850oC for 15 hours. The resulting film was then characterized for its sensitivity value. The film was utilized as a light sensor to read changes in light intensity to monitor lighting status in an Arduino Uno-based energy-saving automatic light prototype. Previously, the output of the film in the form of an electrical voltage was strengthened using a voltage amplifying circuit (OP-Amp). The energy-saving automatic light prototype was manufactured in two conditions, an automatic condition (with assistance from an infrared passive sensor and real time clock) and a manual condition (with assistance from a GSM to control the lighting and LiTaO3 film as a light sensor to monitor the lighting status). In the automatic condition, the assessment of the infrared passive sensor's sensitivity was conducted at distances of 0 m, 0.5 m, 1 m, 1.5 m, 2 m, 2.5 m, and 3 m at angles of 00, 300, 450 and 600 (the source of motion was human movements). The real time clock was used to regulate the infrared passive sensor activation time (7 a.m to 5 p.m Western Indonesia Time). In the manual condition, when entering manual time (outside the 7 a.m to 5 p.m Western Indonesia Time range), to be exact, the GSM would send a message containing the duration of the lighting usage and the cost of the lighting usage. Activation of the lighting was conducted by replying to the message with the code #1 to turn on the lighting and #0 to turn it off.
The growth of Ba0.55Sr0.45TiO3 films on p-type silicon substrate with depletion and enhancement treatments have been conducted in this research. The aims were to examine film sensitivity as light sensor and value range, resolution, acuracy level, and their hysteresis as temperature sensor. The films were annealed at 800, 850, and 900 °C for 15 hours. In this work, enhancement BST of 850 °C was the best quality film and utilized as light and temperature sensors. Its implementation has been successfully conducted on ATMega8535 microcontroller-based automatic drying system model by exploiting the working principle of the BST films as automatic switch.
22 December 2020 in Jurnal Teknik Pertanian Lampung (Journal of Agricultural Engineering)
Internet of Things (IoT) is a system that connects devices directly or indirectly to the internet. The device can work with remote control. One application of the IoT system on the watering system is able to provide an approach to the ease in the process of growth and development of plants. The research carried out was applied to an IoT-based smart plant watering device. The tool is supported with a soil moisture measuring sensor that acts as a benchmark to determine the condition of soil moisture and automatic control of the process of watering plants. The process of watering plants is scheduled in the morning and evening. Information, as long as the device is run will be displayed on the LCD and screen of an Android-based smartphone application. The data can be a comparison value to determine the suitability of soil moisture data in plants. The volume of water supplied in the watering process also affects the level of soil moisture. IoT-based smart plant sprinklers can automate watering by measuring the percentage of soil moisture as a benchmark for providing water during the watering process. Remote watering control can also be done on this tool by using a WiFi signal to the same access point that is connected to the smartphone client and microcontroller. Keyword: agriculture, automatic sprinklers, engineering, IoT
18 November 2021 in Unri Conference Series: Community Engagement
Partners realize that the production of cultivated fish can still be increased, one of which is by monitoring water quality by providing aeration to maintain water health. Partners need a technological assistance that can improve the quality of results and production levels in a shorter time, and of course not incur large electricity costs from using this technology. This community service program activity is designed to solve partner problems. The proposal team provided a technology product called E-Ox Level, a proven technology to monitor pond water quality and control the aerator engine to keep it at optimum water quality standards. This technology is energy efficient, because it utilizes solar energy. This product can reduce operating costs and increase production yields. This program shows positive results. The results of its installation in the Budikdamber pond showed that the growth rate of fish length and weight was faster than the pond without the help of technology, and the mortality rate was recorded to be lower. These results are similar when the technological device is applied to larger biofloc ponds.
The increasing stock condition of cotton combed 30s t-shirts causes Convection to require optimal production planning, influenced by demand, safety stock, and selling price. The analysis of forecasting demand for t-shirts obtained a need for 217 t-shirts using the Multiplicative Decomposition forecasting method with MAD = 22.47 and MAPE = 0.17. Based on demand data for 1 year, the Safety Stock that must be maintained is 126 shirts/month or 3 shirts/week. The optimal production defuzzification results are 369 t-shirts with 81 fuzzy rules used. The Master Production Planning (MPS) directs the production schedule to be carried out in January, scheduled for the 4th week of December the previous year, as many as 123 shirts and ended on the third Sunday in January as many as 92 shirts to maintain stock conditions and meet the demand of consumer.
30 September 2020 in Jurnal Teknik Pertanian Lampung (Journal of Agricultural Engineering)
The embedded systems in the industrial, especially image processing, is increasingly leading to the study of production automation systems such as fruit sorting. Post-harvest sorting system implemented by the industry is manual, so it’s not effective. The solution was to conduct research aimed at modifying post-harvest sorting tools by engineering tomato and orange sorting machines based on their color. The method uses image processing. It’s the most efficient alternative in terms of cost and complexity of hardware design, does not require many sensors, but produces an accurate output. The camera is placed on the mechanical sorting machine system, taking images to determine the sorting execution after the fruit color type are recognized. The results of the research were carried out through several tests, namely: light intensity, color image data, and organoleptics. Light intensity test showed that the position of the tool had a value of 0.78% of the outside light disturbance. Color image shows the range of ripeness values (R/G) for raw tomatoes 0<=1.04; half ripe tomatoes 1.04<=1.39; ripe tomatoes 1.39<=3.59; raw orange 0<=0.92; undercooked oranges 0.92<=0.98; and ripe oranges 0.98<=1.66. Organoleptic test from five observers had the same results as the reading on the fruit sorting tool. Keywords : engineering, fruit maturity, oranges, sorting machines, tomatoes